Blending Tips; Storing Your Appliance - Oster OBL232X Manual Del Usuario

USING PULSE FUNCTION
1. Plug blender into appropriate electrical outlet.
2. Press power " " button to switch unit on.
3. Turn the Speed Selection Dial to select desired speed.
4. Press pulse " " button to blend and release when done. While pressing pulse "
5. If you wish to change speed simply turn the Speed Selection Dial clockwise to increase it or counter clockwise to reduce it.
6. Repeat step 4.
7. If you are done blending, press power " " button to switch unit off. The Power Button Indicator Light will turn off.
8. Unplug unit from electrical outlet.
This product is pre-programmed to turn off automatically if not used for a period of several minutes. All lights will turn off when the unit
automatically powers down.

BLENDING TIPS

LIQUIDS
Put liquids into the jug first, unless the recipe says otherwise.
Using the jug lid food chute
Do not remove the lid while in use. Food may splatter if you do. Instead, open the jug lid cap to
add smaller ingredients.
Working with Hot Foods or Liquids
WARNING: When you work with HOT FOODS, remove the jug lid
food chute to vent steam. Tilt the lid away from you partially
covering the opening. Keep hands and other exposed skin away from
the lid opening to prevent possible burns.
When you work with HOT LIQUIDS, remove the jug lid food chute and
start at a low speed, and then gradually increase to a faster speed. Do
not add liquid over the cup (1L) level. Always keep hands away from
steam. Do not blend boiling liquids in the blender.
Ingredients Quantities
Do not overfill the Blending Jug past the 1.25L (5 Cups) fill line. Overfilling may create a hazard and damage the blender. If you want
greater amount, prepare in batches. Using larger amounts may overload and strain the motor.
Frequently Asked Questions
Why doesn't the blender/food processor turn on?
• Make sure the base is plugged in an active power receptacle.
• Verify red light is active after pushing on/off button.
How can I prevent liquids from leaking out?
Check to see that the sealing ring is correctly assembled in between the jug blade and the jug.
6
" button.
AFTER USE:
1.
2.
CLEANING
Release the Special 6-Point Blade with Jug Bottom, from the bottom of the jug by turning
the jug bottom counterclockwise.
The jug lid, jug lid cap and blade are dishwasher safe. Use the top rack of the dishwasher for
the jug lid, jug lid cap, and blade.
You can also wash the parts in warm, soapy water. Rinse well and dry. Wipe the base with a
soft, damp cloth to clean. Never submerge the low profile base in a liquid. Check the parts as
you put them back together.
Reassemble the blender for storage. Do not fully close the lid, this will prevent any odour build up.
If the plug is not suitable for the socket outlets in your home, it can be removed and replaced by a plug of the correct type.
If the fuse in a moulded plug needs to be changed, the fuse cover must be refitted. The appliance must not be used without the fuse cover
Figure 5 fitted.
If the plug is unsuitable, it should be dismantled and removed from the supply cord and an appropriate plug fitted as detailed. If you remove the
plug it must not be connected to a 13 amp socket and the plug must be disposed of immediately.
If the terminals in the plug are not marked or if you are unsure about the installation of the plug please contact a qualified electrician.
CARING AND MAINTAINING YOUR OSTER BLENDER
WITH REVERSIBLE MOTOR
Lift the jug from the base, remove the lid and empty the jug.
If necessary, use a rubber spatula to scrape foods away from the sides of the jar.

STORING YOUR APPLIANCE

ELECTRICAL SAFETY (UK & IRELAND)
This symbol indicates that this unit is a Class II appliance and therefore an earth connection is not required.
Plug should be ASTA approved to BS1363
Fuse should be ASTA approved to BS1362
Do Not Connect
Mains Wires Here
Blue
(Neutral)
Ensure that the outer sheath of
the cable is firmly held by the cord grip
Fuse 13A
Brown
(Live)
7