Connecting The Baby Unit To The Ac Mains; Initial Use - Topcom BABYVIEWER 4500 Manual De Usuario

®
7.1 Baby unit components
A
See Figure on the fold-out page.
1 On/off LED
2 Night light LED
3 Infrared LED for night
vision
4 On/off switch
5 Lens
6 Microphone
7 Wall mounting cavity
7.2 Parent unit components
See Figure on the fold-out page.
B
14 Volume LED
15 Microphone
16 Increase volume /
Next menu item
17 Decrease volume /
Previous menu item
18 Play button
19 Lullaby button
20 3,5" (8,8cm) colour display
21 VOX on/off LED
7.3 Display description
Out of range or no
connection
Volume icon
Melody icon
8

Initial use

8.1 Package content
The equipment is supplied as standard with the following items:
- 1 baby unit
- 1 parent unit
- 2 AC mains adapters
8.2 Installing batteries in the baby unit
• You can operate the baby unit with 4 AAA
cells (LR03; we recommend alkaline cells)
or the included AC mains adapter.
• The baby unit cannot recharge batteries.
• It is recommended to always leave the
batteries in the unit, even if you use the AC
mains adapter. The unit will automatically
switch to battery power in case of a mains
power interruption.
– Turn the screw on the cover of
the battery compartment
at the back of the baby unit
90° counter clockwise and
remove the battery
compartment cover.
Do not turn the screw past the "OPEN" point.
4
8 Crib connector nut
9 Light sensor
10 Battery cover with screw
11 Speaker
12 Connector for AC mains
adapter
13 Room temperature sensor
22
23 Power on/off LED
24 Menu button
25 Push to Talk button
26 On/off button
27 Belt clip
28 Speaker
29 Connector for AC mains
adapter
30 Battery cover with screw
LCD display
brightness icon
Temperature unit
C
icon
Night light icon
- 1 user guide
- 1 service card
- 1 Li-ion rechargeable battery pack
10
OPEN
90° MAX
– Fit four AAA alkaline
cells (LR03) in the
battery compartment.
Ensure that the polarity is
correct.
– Close the battery
compartment.
Never mix used cells with fresh cells.
8.3

Connecting the baby unit to the AC mains

Insert the small plug of the
AC mains adapter in the
PTT PTT
mains power connector of
the baby unit 12 and plug
the AC mains adapter into a
mains connector (100~240
V - 50/60 Hz).
CAUTION
• The mains connector must be within easy reach so
you can quickly unplug the power cable in an
emergency.
• Use only the supplied AC mains adapter (6 V DC /
800 mA).
8.4 Installing the rechargeable battery pack in
the parent unit
B
See Figure on the fold-out page.
CAUTION
• Use only the supplied Li-ion battery pack in the parent
unit.
– Rotate the belt clip
upward.
26
– Turn the screw on the
cover
29
battery compartment
at the back of the
parent unit 90°
counter clockwise and
remove the battery
compartment cover.
Do not turn the screw past the "OPEN" point.
– Place the Li-ion battery pack in the battery compartment.
Ensure that the battery contacts do make contact with
the charge contacts as illustrated.
– Carefully close the battery compartment and rotate the
belt clip back downwards.
8.5 Connecting the parent unit to the AC mains
– Insert the small plug of the AC mains adapter in the
mains power connector
adapter into a mains connector (100~240 V - 50/60 Hz).
It takes around 10 hours to fully charge the
batteries.
Babytalker 3500 SEDS
of the
and plug the AC mains
28