KTM Power Parts 61108200000 Instrucciones De Montaje página 10

Scope of supply
2x Distance bushing for rear top section
2x DIN 7984 M8x18 cylinder screw
2x Plug
1x Seat carrier
6x Rubber spacer for seat
1x Lock plate for seat carrier
3x EJOT PT screw, 50x18 WN 1413
1x Seat, complete R
2x Washer, D=16.5mm
4x AH M6x16 flathead screw
1x Rear top section for monoseat
1x Edge protection
2x Mounting plate for rear top section (left and right)
6x EJOT PT screw, 50x18 WN 1411
1x Mounting plate for taillight
2x M6 INOX range change nut
2x M6x12 oval head screw, ISO 7380
1x Seat pin
1x Retaining bracket for rear top section lock
10x M6x25 flat-head screw, DIN 7991
2x M6 range change metal nut
2x Rubber spacer for airbox
1x Rear lower section for monoseat 05/06 (Kit 61108200000) 61108219000
1x Rear lower section for monoseat 07 (Kit 61108200100)
2x Retaining bracket for wiring harness
2x EJOT PT screw, 40x18 WN 1412
1x Seat carrier bracket
10
2x 6x11x16x5mm collared bush
2x Collet for rear lower section
2x Mounting bolt for rear lower section
10 x KTM M6x15 collar screw
10 x KTM M6x25 collar screw
10 x EJOT PT 60x30 screw
1x Upper license plate bracket
1x Lower license plate bracket
6x EJOT PT screw K60x20
4x distance bushing 7mm
10 x M6x20 cylinder screw, DIN 6912
4x 15mm distance bushing
4x M6x30 AH screw, DIN 6912
1x LED EU 07 taillight
10 x KTM M5x12 collar screw
1x RSGU clamp
3x EJOT PT screw, KA 50x12
1x License plate lamp
1x 50x3.5x8 EJOT Easyboss
1x Rear top section lock 08
1x Seat lock lever, complete 05
1x Retaining bracket lever for seat lock 07
1x M5 range change metal nut
1x Lock plate for seat lock 07
10 x KTM M6x16 collar screw
1x cable clip
1x KHS cable clip
1x Heat-resistant film
10x DIN 9021 A 6.4 washer
NOTE: The conversion kit is delivered unpainted. Paint before mounting.
The original heat shields for the silencers cannot be used when the Super
Duke-R Kit is mounted. Optional carbon heat shields are available under order num-
ber
6110519002049 (left)
6110519003049 (right).
No heat shields are required if you are using an Akrapovic Evolution exhaust system.
NOTE: Use the tightening torques specified in the torque list in the Owner's Manual.
61108128000
0984080183
61103165000
61107147000
61007040010
61107147060
0017050181
61107140000
60008045000
0984060163
6110811800033
61108118070
61108118080
0081500181
61108118085
54603048300
0738060121
61107140060
61108118090
0991060253
54603048100
60006001021
61108119000
61108119080
0016040183
61107149000
50308052000
61110829000
61108130000
0014060153
0014060253
0017060303
61108122000
61108115000
0017060203
61107148007
0984060203
61107148015
0984060302
75014040000
0015050123
58711070000
0081050121
75014047000
0040503508
61107050044
58607051044
61107154100
54603048200
61107153000
0015060163
61111041000
58111076000
61108121000
0021060003