Maintenance And Repair; Blade Care - GreenWorks 2200607 Manual De Utilización

EN
FR DE ES
mm thick, or hose obviously too large to feed into he
cutting blade. Use a non-powered hand saw or pruning
saw to trim large stems.
„ If desired, you can use a string to help cut your hedge
level. Decide how high you want the hedge. Then,
stretch a piece of string along the hedge at this height.
Trim he hedge just above this guide line of string. See
Figure 5. Trim the side of a hedge so that it will be
slightly narrower at the top. See Figure 6. More of he
hedge will be exposed when shaped this way, and it
will be more uniform. If blades do become jammed,
stop the motor, allow the blades to stop and remove
the battery pack before attempting to remove he
obstruc ion.
„ Wear gloves when trimming thorny or prickly growth.
When trimming new growth, use a wide sweeping
action, so that the stems are fed direc ly into the cutting
blade. Older growth will have thicker stems and will be
trimmed easiest by using a sawing movement.
If blade jams on any electrical cord or line, DO NOT
TOUCH THE BLADE! IT CAN BECOME ELECTRICALLY
LIVE AND VERY DANGEROUS. Continue to hold the
hedge trimmer by the insulated rear handle or lay it
down and away from you in a safe manner. Disconnect
the electrical service to the damaged line or cord before
attempting to free the blade from the line or cord. Failure
to heed his warning will result in serious personal injury
or possible death.
Clear the area to be cut before each use. Re-move all
objects such as cords, lights, wire, or string which can
become entangled in the cutting blade and create a risk
of serious personal injury.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types
of commercial solvents and may be damaged by their
use. Use a clean cloth to remove dirt, oil,grease, etc.
When servicing use only iden ical Greenworks Tools
replacement parts. Use of any other parts can create a
hazard or cause product damage.
IT PT NL SV DA NO
English (Original instructions)
DanGer
WarninG
WarninG
FI HU CS RU RO PL
Do not at any time let brake fluids, gasoline, petroleum
based products, penetrating oils, etc., come in contact
with plastic parts. They contain chemicals that may
damage, weaken, or destroy plas ics.

MaintenanCe anD repair

BlaDe MaintenanCe – HeDGe triMMer
Battery units do not have to be plugged into an electrical
outlet; therefore, they are always in operating condition.
To prevent serious personal injury, always remove
the battery and take extra precautions and care when
performing maintenance, service or for changing the
cutting blade.
To prevent serious personal injury, remove he battery
pack before servicing, cleaning, or removing material
from the unit.

BlaDe Care

„ Lubricate the cutting blades after each use.
„ Periodically inspect the blades for damage and wear.
„ Always use the manufacturer's specified replacement
blades.
to luBriCate BlaDe See figure 7.
„ Remove battery pack from hedge trimmer.
„ For easier operation and longer blade life, lubricate the
hedge trimmer blade before and after each use. Before
lubricating, remove the battery pack and lay hedge
trimmer on a flat surface. Apply light weight machine oil
along the edge of the top blade.
„ Occasionally, you should oil your hedge trimmer during
prolonged use. Before oiling, stop hedge trimmer,
remove battery pack, then oil. You then can resume
trimming. Do not oil while hedge trimmer is running.
HeDGe triMMer luBriCation
„ All of the bearings in this tool are lubricated with a
sufficient amount of high-grade lubricant for the life of
the unit under normal operating procedures. Therefore,
no fur her lubrication is required.
16
SL HR ET LT LV SK BG
Caution
WarninG
WarninG