Technical Data; Ec Declaration Of Conformity; Definitions: Safety Guidelines; Safety Instructions - DeWalt DW711 Manual De Instrucciones

eng lis h
TaBLe ToP miTre saW
dW711
Congratulations!
You have chosen a D WALT tool. Years of experience, thorough product
e
development and innovation make D
partners for professional power tool users.

Technical data

Voltage
Power input
Power output
Max. blade speed
blade diameter
blade bore
Blade body thickness
Riving knife thickness
Riving knife hardness
Weight
CUTTTing CaPaCiTies
Mitre saw mode
Mitre (max. positions)
Bevel (max. positions)
At 90˚, at max. height 50 mm,
max. width of cut
At 45˚ mitre, at max. height 50 mm,
max. width of cut
At 45˚ bevel, at max. height 45 mm,
max. width of cut
At 90˚, at max. depth of cut 96 mm, max width 20 mm, max. cut off 15 mm
Saw bench mode
Max. depth of cut
Fuses:
Europe
U.K. & Ireland

definitions: safety guidelines

The definitions below describe the level of severity for each signal word.
Please read the manual and pay attention to these symbols.
dANGer: Indicates an imminently
hazardous situation which, if not avoided, will result in death or
serious injury.
WArNING: Indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a
potentially hazardous situation which, if not avoided, may result
in property damage.
Denotes risk of electric shock.
Denotes risk of fire.
Denotes sharp edges.
20
WALT one of the most reliable
e
DW711 DW711-LX
V 230
W 1300
W 900
min
2,950
-1
mm 247-260 247-260
mm 30
mm 2.0
mm 2.3
mm 43 ±5
kg 20
left 50˚
right 50˚
left 48˚
right 0˚
mm 134
mm 94
mm 134
mm 0-50
230 V tools 10 Amperes, mains
230 V tools 13 Amperes, in plugs
eC-declaration of conformity
dW711/dW711-LX
D WALT declares that these Power Tools have been designed in
e
compliance with: 98/37/EEC, 89/336/EEC, 73/23/EEC, EN 61029-1,
115
EN 61029-2-11, EN 55014, EN 55014-2, EN 61000-3-2, EN 61000-3-3.
1100
For more information, please contact D
800
to the back of the manual.
2,950
Level of sound pressure according to 86/188/EEC & 98/37/EEC, measured
according to EN 61029-2-11:
30
2.0
2.3
L (sound pressure)
pA
43 ±5
L (acoustic power)
WA
20
*at the operator's ear
WArNING: Take appropriate measures for the protection
of hearing.
50˚
Weighted root mean square acceleration value according to
50˚
EN 61029-2-11:
48˚
0˚
134
TÜV Rheinland
94
Product and Safety GmbH (TRPS)
Am Grauen Stein 1
D-51105 Köln
134
Germany
0-50
Horst Grossmann
Vice President Engineering and Product Development
D WALT, Richard-Klinger-Straße 11,
e
D-65510, Idstein, Germany

safety instructions

WArNING: When using stationary power tools, always observe
the safety regulations applicable in your country to reduce the
risk of fire, electric shock and personal injury. Read all of this
manual carefully before operating the tool. Save this manual for
future reference.
General
1. Keep work area clean.
Cluttered areas and benches can cause accidents.
2. Consider work area environment.
Do not expose the tool to rain. Do not use the tool in damp or wet
conditions. Keep the work area well lit (250 - 300 Lux). Do not use
the tool where there is a risk of causing fire or explosion, e.g. in the
presence of flammable liquids and gases.
3. Keep children away.
Do not allow children, visitors or animals to come near the work area or
to touch the tool or the mains cable.
WALT at the address below or refer
e
DW711
dB(A)* 89
dB(A) 102
DW711
< 2.5 m/s
2
Cert. No.
BM 60013858 0001
DW711-LX
89
102
DW711-LX
< 2.5 m/s
2