Charging Procedure; Environmental Protection; Declaration Of Conformity - Worx WA3750.1 Manual Del Usuario

CHARGING PROCEDURE

NOTE: Before using the charger, read the
instruction book carefully.
HOW TO USE YOUR CHARGER
1. Plug charger directly into an electrical outlet.
ABUSE THE CORD. Never carry charger by cord. Do not
disconnect the charger from the outlet by pulling it by the
cord.
2. CAUTION: To reduce the risk of fire,
electrical shock, or personal injury do not attempt to
use this charger with any other product.
Likewise, do not attempt to charge the mower with any
other charger.
3. Do not operate a damaged charger. Replace damaged
cords or charger immediately at an authorized WORX
service depot.
4. Do not charge in wet locations. Do not charge mower when
temperature is above 104°F (40°C) or below 41°F (5°C).
5. Keep the mower and charger away from water, heat
sources, (such as radiators, heaters, stoves...etc.) flames, or
chemicals. Be careful not to damage the charger cord, by
keeping cord away from sharp edges.
CONNECTING THE CHARGING STATION (See Fig.
A.B)
1. When connecting the charging base's power cord to the
adapter, align the notch on the power cord (b) with the
groove on the adapter (a).
2. Connect the charger's power cord to a wall socket. It is
preferable to use an earth-fault breaker as recommended.
CHARGING A DISCHARGED BATTERY (See Fig. C)
When Landroid is new or has been stored for a long period,
®
the battery will not be charged and needs to be charged before
starting.
1) Place Landroid in the working area.
®
2) Press on/off key to start. Press HOME then OK to send
Landroid back to the charging base.
®
3) The charging base green light will be flashing, Landroid
begin to charge.
MAINTENANCE
Remove the plug from the socket before carrying out any
adjustment, servicing or maintenance.
Your charger requires no additional lubrication or maintenance.
Never use water or chemical cleaners to clean your charger.
Wipe clean with a dry cloth. Always store your charger in a dry
place.

ENVIRONMENTAL PROTECTION

Waste electrical products must not be disposed of with
household waste. Please recycle where facilities exist.
Check with your local authorities or retailer for recycling
advice.
PLUG REPLACEMENT
(UK & IRELAND ONLY)
If you need to replace the fitted plug then followthe instructions
below.
IMPORTANT
The wires in the mains lead are colored in
accordance with the following code:
Blue – Neutral
Brown – Live
As the colors of the wires in the mains lead of thisappliance
DO NOT
may not correspond with the coloured markings identifying
the terminals in your plug,proceed as follows. The wire which
is coloured blue must be connected to the terminal which is
marked with N. The wire which is coloured brown must be
connected to the terminal which is marked with L.
Warning:
terminal of the plug. Only fit an approved BS1363/A plug
and the correct rated fuse.
Note: If a moulded plug is fitted and has to be removed take
great care in disposing of the plug and severed cable, it must be
destroyed to prevent engaging into a socket.
Connect
Blue to N
(neutral)
Outer sleeve
firmly clamped

DECLARATION OF CONFORMITY

We,
POSITEC Germany GmbH
Grüner Weg 10, 50825 Cologne, Germany
Declare that the product,
Description
Type WA3750.1
Complies with the following Directives,
2014/35/EU
will
®
2014/30/EU
2011/65/EU
Standards conform to
EN 60335-1:2012+A11:2014,
EN 60335-2-29:2004+A2:2010,
EN 62233:2008,
EN 55014-1:2006+A1:2009+A2:2011,
EN 55014-2:2015,
EN 61000-3-2:2014,
EN 61000-3-3:2013,
EN 61558-1:2005+A1:2009,
EN 61558-2-16:2009+A1:2013
2018/11/02
Allen Ding
Deputy Chief Engineer Testing & Certification
Positec Technology (China) Co., Ltd
18, Dongwang Road, Suzhou Industrial
Park, Jiangsu 215123, P. R. China
Never connect live or neutral wires to the earth
13 Amp fuse approved
to BS1362
Brown L (live)
Cable grip
WORX Battery Charger
EN
5