Briggs & Stratton 1200A Manual Del Usuario página 5

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 53
Step 2: Oil and Fuel
Oil Recommendations Figure
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF
or higher. Do not use special additives.
Outdoor temperatures determine the proper oil viscosity
for the engine. Use the chart to select the best viscosity
for the outdoor temperature range expected.
* Below 4°C (40°F) the use of SAE 30 will result in hard starting.
** Above 27°C (80°F) the use of 10W30 may cause increased oil
consumption. Check oil level more frequently.
Checking/Adding Engine Oil Figure
Oil level should be checked prior to each use or at least
every 8 hours of operation. Keep oil level maintained.
1. Make sure generator is on a level surface.
2. Clean area around oil fill (1,H) and remove oil fill
cap/dipstick.
3. Verify oil is at Full mark (3,A) on dipstick.
4. If needed, slowly pour oil into oil fill opening to Full
mark on dipstick. Do not overfill.
5. Replace and tighten oil fill cap/dipstick.
NOTICE Do not attempt to crank or start engine before
before it has been properly serviced with recommended
oil. This could result in an engine failure.
CAUTION Avoid prolonged or repeated skin
contact with used motor oil and fuel. Used motor
oil has been shown to cause skin cancer in
certain laboratory animals. Thoroughly wash exposed
areas with soap and water.
KEEP OUT OF REACH OF CHILDREN. DON'T
POLLUTE. CONSERVE RESOURCES. RETURN
USED OIL TO COLLECTION CENTERS.
Add Fuel Figure
4
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline with a minimum of
87 octane/87 AKI (91 RON).
• Gasoline with up to 10% ethanol content is acceptable.
NOTICE Do not mix oil in gasoline or modify engine to
run on alternate fuels. Do not use unapproved gasoline
such as E15 and E85. Use of unapproved fuels could
damage generator and voids warranty.
See High Altitude for 1,524 m (5,000 ft.) and above.
2
1 3
WARNING! Fuel and its vapors are
extremely flammable and explosive
which could cause burns, fire or
explosion resulting in death or serious injury. Do not
refuel during operation. Turn engine off and let it cool at
least 2 minutes before removing fuel cap. Fill fuel tank
outdoors. Do not spill fuel. Keep fuel away from sparks,
open flames, pilot lights, heat, and other ignition sources.
Check fuel lines, tank, cap and fittings frequently for
cracks or leaks. Replace if necessary. Do not light a
cigarette or smoke. Do not pour water on generator to
put out fire. Only use a extinguisher rated for flammable
liquids and electrical systems such as a powder
extinguisher. Follow the instructions provided by fire
extinguisher manufacturer before use. This generator is
not for use in explosive atmospheres.
1. Slowly remove fuel cap to relieve pressure in tank.
2. Slowly add unleaded fuel (A) to fuel tank (B). Be
careful not to fill above lip (C). This allows adequate
space for fuel expansion.
3. Install fuel cap and let any spilled fuel evaporate
before starting engine.
High Altitude
At altitudes over 1524 m (5,000 ft.), a minimum
85 octane/85 AKI (89 RON) fuel is acceptable. To remain
emissions compliant, high altitude adjustment is required.
Operation without this adjustment will cause decreased
performance, increased fuel consumption, and increased
emissions.
See an Authorized Briggs & Stratton dealer for high
altitude adjustment information. Operation of the engine
at altitudes below 762 m (2,500 ft.) with the high altitude
kit is not recommended.
Transporting
When transporting equipment with a vehicle or trailer,
turn fuel shutoff valve to OFF (0) position. Do not tip
engine or equipment at angle which causes fuel to spill.
Cleaning
Daily or before use, look around and underneath
generator for signs of oil or fuel leaks. Clean any
accumulated debris. Keep area around muffler free from
any debris.
• Use a soft bristle brush to loosen caked on dirt or oil.
• Use a damp cloth to wipe exterior surfaces clean.
NOTICE Do not insert any objects through cooling slots.
5

Publicidad

Tabla de contenido
loading

Tabla de contenido