Description (Fig. A) - DeWalt DCFS950 Traducido De Las Instrucciones Originales

Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Visible radiation. Do not stare into light.
Length of staples.
40-50mm
9GA
Staple thickness.
3.7-4.0mm
38
Loading capacity.
Suitable staple collation angle.
0°
Date Code Position (Fig. A)
The date code , which also includes the year of manufacture,
17
is printed into the housing.
Example:
2019 XX XX
Year of Manufacture

Description (Fig. A)


WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Trigger
1
Trigger lock-off
2
Tool free speed select
3
Tool free mode select
4
Utility hook
5
Tool free depth adjust
6
Contact trip
7
Intended Use
Your fencing stapler is intended ONLY for use in driving staples
into wood. This tool has two operating modes, a sequential
operating mode and a unique rapid sequential operating mode
(RapidCycle). Read the section of the manual Selecting the
Mode before using the tool to make sure you are selecting the
proper mode for your application.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
Your fencing stapler is a professional power tool.
Only D WALT staples meeting applicable building code
e
requirements should be used in this tool.
This tool is intended for use by construction professionals.
Tool free stall release
8
LED work lights (x2)
9
Magazine
10
Magazine release
11
Pusher
12
Battery release button
13
Battery
14
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Dry Fire Lock Out
Your stapler is equipped with a dry fire lockout which prevents
the tool from actuating when the magazine is nearly empty.
When 5 staples remain in the magazine, the tool ceases
to operate. Refer to Loading the Tool to reload a stick of
collated staples.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack 14
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 13
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
EnGLIsh
WALT battery packs and chargers.
14 is fully charged.
with the rails inside the tool's
and firmly pull the battery pack
which
23
43