Bosch GCM 10 MX Manual Original página 23

22 | English
If the cut-off piece or workpiece tips, it can lift the lower
guard or be thrown by the spinning blade.
Do not use another person as a substitute for a table
u
extension or as additional support. Unstable support
for the workpiece can cause the blade to bind or the
workpiece to shift during the cutting operation pulling you
and the helper into the spinning blade.
The cut-off piece must not be jammed or pressed by
u
any means against the spinning saw blade. If confined,
i.e. using length stops, the cut-off piece could get wedged
against the blade and thrown violently.
Always use a clamp or a fixture designed to properly
u
support round material such as rods or tubing. Rods
have a tendency to roll while being cut, causing the blade
to "bite" and pull the work with your hand into the blade.
Let the blade reach full speed before contacting the
u
workpiece. This will reduce the risk of the workpiece be-
ing thrown.
If the workpiece or blade becomes jammed, turn the
u
mitre saw off. Wait for all moving parts to stop and
disconnect the plug from the power source and/or re-
move the battery pack. Then work to free the jammed
material. Continued sawing with a jammed workpiece
could cause loss of control or damage to the mitre saw.
After finishing the cut, release the switch, hold the
u
saw head down and wait for the blade to stop before
removing the cut-off piece. Reaching with your hand
near the coasting blade is dangerous.
Hold the handle firmly when making an incomplete cut
u
or when releasing the switch before the saw head is
completely in the down position. The braking action of
the saw may cause the saw head to be suddenly pulled
downward, causing a risk of injury.
Keep your work area clean. Material mixtures are partic-
u
ularly hazardous. Light metal dust may catch fire or ex-
plode.
Do not use dull, cracked, bent or damaged saw blades.
u
Unsharpened or improperly set saw blades produce
narrow kerf causing excessive friction, blade binding
and kickback.
Do not use saw blades made from high speed steel
u
(HSS). Such saw blades can easily break.
Always use saw blades with correct size and shape
u
(diamond versus round) of arbour holes. Saw blades
that do not match the mounting hardware of the saw will
run off-centre, causing loss of control.
Never remove cuttings, wood chips, etc. from the cut-
u
ting area while the power tool is running. Always guide
the tool arm back to the neutral position first and then
switch the power tool off.
Do not touch the saw blade after working before it has
u
cooled. The saw blade becomes very hot while working.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
1 609 92A 5U4 | (07.10.2020)
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Symbols
The following symbols may be important for the operation of
your power tool. Please take note of these symbols and their
meaning. Correctly interpreting the symbols will help you to
operate the power tool more effectively and safely.
Symbols and their meaning
Keep hands away from the cutting area
while the power tool is running. Con-
tact with the saw blade can lead to injur-
ies.
Wear a dust mask.
Wear safety goggles.
Wear hearing protection. Exposure to
noise can cause hearing loss.
Danger area! Keep hands, fingers and
arms away from this area.
Take note of the dimensions of the saw
30mm
blade. The hole diameter must fit the tool
spindle without play. If it is necessary to
use reducers, ensure that the dimensions
of the reducer are suitable for the base
blade thickness and the saw blade hole
diameter, as well as the tool spindle dia-
meter. Wherever possible, use the redu-
cers provided with the saw blade.
The saw blade diameter must match the
information specified on the symbol.
When sawing bevel angles, the adjustable
fences must be pulled outwards or re-
moved completely.
Autogoods "130"
Bosch Power Tools