Maintenance And Servicing - Bosch GCM 10 MX Manual Original

28 | English
– Turn the saw table (7) to the 0° detent (45). The lever
(11) must be felt to engage in the detent.
– Pull the adjustable fence (17) all the way out.
Checking (see figure O1)
– Set an angle gauge to 90° and position it flush with the
saw blade (41) between the fence (6) and the saw blade
on the saw table (7).
The leg of the angle gauge must be flush with the fence over
the complete length.
Setting (see figure O2)
– Loosen all hex socket screws (47) with the hex key (22)
provided.
– Rotate the fence (6) until the angle gauge is flush over the
complete length.
– Re-tighten the screws.
Setting the Standard 0° Bevel Angle
– Bring the power tool into the transport position.
– Turn the saw table (7) to the 0° detent (45). The lever
(11) must be felt to engage in the detent.
Checking (see figure P1)
– Set an angle gauge to 90° and place it on the saw table
(7).
The leg of the angle gauge must be flush with the saw blade
(41) along its entire length.
Setting (see figure P2)
– Loosen the clamping handle (26).
– Loosen the lock nut of the stop screw (33) using a com-
mercially available ring spanner or open-ended spanner
(13 mm).
– Turn the stop screw as far in or out as needed until the leg
of the angle gauge is flush with the saw blade along its en-
tire length.
– Retighten the clamping handle (26).
– Then retighten the lock nut of the stop screw (33).
If the angle indicator (31) is not aligned with the 0° mark on
the scale (32) following adjustment, loosen the screw (48)
using a commercially available cross-headed screwdriver
and align the angle indicator along the 0° mark. (See figure
R)
Setting the standard 45° bevel angle
– Bring the power tool into the work position.
– Turn the saw table (7) to the 0° detent (45). The lever
(11) must be felt to engage in the detent.
– Loosen the clamping handle (26) and use the handle (3)
to swivel the tool arm all the way to the left (45°).
Checking (see figure Q1)
– Set an angle gauge to 45° and place it on the saw table
(7).
The leg of the angle gauge must be flush with the saw blade
(41) along its entire length.
Setting (see figure Q2)
– Loosen the lock nut of the stop screw (23) using a com-
mercially available ring spanner or open-ended spanner
(13 mm).
1 609 92A 5U4 | (07.10.2020)
– Turn the stop screw as far in or out as needed until the leg
of the angle gauge is flush with the saw blade along its en-
tire length.
– Retighten the clamping handle (26).
– Then retighten the lock nut of the stop screw (23).
If the angle indicator (31) is not aligned with the 45° mark on
the scale (32) following adjustment, first check the 0° set-
ting for the bevel angle and the angle indicator once more.
Then repeat the adjustment of the 45° bevel angle.
Transport (see figure S)
Before transporting the power tool, the following steps must
be carried out:
– Bring the power tool into the transport position.
– Remove all accessories that cannot be securely fitted to
the power tool.
If possible, transport unused saw blades in a closed con-
tainer.
– Carry the power tool by the transport handle (28) or hold
it by the recessed handles (15) on the sides of the saw
table.
Only use the transport devices to transport the power
u
tool and never the protective devices.

Maintenance and servicing

Maintenance and cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
The retracting blade guard must always be able to move
freely and retract automatically. It is therefore important to
keep the area around the retracting blade guard clean at all
times.
Always remove dust and chips after working by blowing out
with compressed air or using a brush.
Accessories
Extension bar
Saw blades for hardwood, composites, plastic and non-
ferrous metals
254 x 30 mm saw blade, 96 teeth
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
Autogoods "130"
Article number
1 619 PA6 916
2 608 640 451
Bosch Power Tools