Bosch GCM 10 MX Manual Original página 25

24 | English
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 92 dB(A); sound power level
105 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
Avoid starting the power tool unintentionally. The
u
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items included
See the list of items included at the start of
the operating manual.
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Mitre saw with mounted saw blade
– Dust bag (19)
– Screw clamp (18)
– Hex key/cross-headed screwdriver (22)
– Tilt protector (24) with fastening set (35) (2 bolts, 2
washers, 2 square nuts)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Fitting individual components
– Carefully remove all parts included in the delivery from
their packaging.
1 609 92A 5U4 | (07.10.2020)
– Remove all packing material from the power tool and the
accessories provided.
Mounting the tilt protector (see figure A)
Before the power tool is used for the first time, the tilt
protector (24) must be installed.
Use the "tilt protector" fastening set (35) for the installation.
– Insert the square nuts (35) into the corresponding
holes (34) in the base plate.
– Place the washers (35) on the fastening screws (35) and
use them to screw the tilt protector (24) into the inserted
nuts.
Do not remove the tilt protector. Without the tilt pro-
u
tector, the power tool will not be stable and can tip over
especially when sawing maximum mitre/bevel angles.
Fitting the extension bar (see figure B)
The free end of long and heavy workpieces must have some-
thing placed underneath it or be supported.
To extend the saw table further, extension bars can be
mounted both to the left or right of the power tool.
– Push the extension bars (36) on both sides of the power
tool all the way into the corresponding drill holes (16).
– Tighten the fastening screws (37) to secure the extension
bars.
Stationary or flexible mounting
To ensure safe handling, the power tool must be
u
mounted on a flat, stable work surface (e.g. work
bench) before use.
Mounting on a work surface (see figure C1−C2)
– Use suitable screw fasteners to secure the power tool to
the work surface. The holes (14) are used for this pur-
pose.
or
– Firmly clamp the base of the power tool to the work sur-
face with commercially available screw clamps.
Mounting on a Bosch saw stand
With the height-adjustable legs, Bosch GTA saw stands
provide firm support for the power tool on any surface. The
workpiece supports of the saw stand are used for underlay-
ing long workpieces.
Read all the warnings and instructions included with
u
the saw stand. Failure to observe the warnings and fol-
low instructions may result in electric shock, fire and/or
serious injury.
Assemble the saw stand properly before mounting the
u
power tool. Correct assembly is important to prevent the
risk of collapsing.
– Mount the power tool on the saw stand in the transport
position.
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
Autogoods "130"
Bosch Power Tools