EngLIsh
Date Code Position (Fig. B)
The date code
8
, which also includes the year of manufacture,
is printed into the housing.
Example:
2021 XX XX
Year and week of Manufacture
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Battery pack
1
Battery release button
2
Trigger switch
3
Forward/reverse control button
4
Anvil
5
Handle
6
Hog ring
7
Intended Use
These impact drivers are designed for professional impact
screwdriving applications. The impact function makes this
tool particularly useful for driving fasteners in wood, metal
and concrete.
DO nOt use under wet conditions or in the presence of
flammable liquids or gases.
These impact drivers are professional power tools.
DO nOt let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
•
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: Use only D
Anvil (Fig. A, D)
WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous condition.
Inspect accessories prior to use to ensure that it con tains
no cracks.
CAUTION: Inspect anvils and hog rings prior to use.
Missing or damaged items should be replaced before use.
Place the switch in the locked off (centre) position or remove
battery pack before changing accessories.
28
WALT battery packs and chargers.
e
to install an accessory on the hog ring anvil, firmly push
accessory onto the anvil
5
the accessory to slide on. After accessory is installed, the hog
ring applies pressure to help provide accessory retention.
to remove an accessory, grasp the accessory and firmly pull
it off.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. C)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOtE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. C)
Some D
WALT battery packs include a fuel gauge which consists
e
of three green LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge
9
button. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level of
charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOtE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
. The hog ring
7
compresses to allow
1
is fully charged.
1
with the rails inside the tool's
2
and firmly pull the battery pack
, press and hold the fuel gauge
6
.