Tabla de contenido
Publicidad
PREPARATION TO WORK
SELECTION OF THE WORKING TOOL
The table shows examples of the use of working tools
HCS blade for wood
Name
Wood, wood-based materials, plastics
Type of
material
Dividing and plunge cutting in corners and
Intended use
hardly accessible places, near surface
Cut outs in furniture boards, cutting cove bases
Example
short, plunge cutting for fitting floor panels
Delta sanding pad
Name
Wood, wood-based materials, abrasive materials
Type of
material
Sanding in hardly accessible places and in corners
Intended use
on a hard ground
Removal of mortar and glue for ceramic tiles,
Example
sanding solid wood, polishing
INSTALLATION AND REPLACEMENT OF SANDING PAPER
Sanding pad is equipped with hook-and-loop attachment system for quick
and easy replacement of sanding paper. Choose sanding paper with
appropriate gradation depending on the processed material and desired
level of material removal. All types of sanding paper, abrasive cloths and
polishing felt are allowed.
• Use only appropriate sanding paper with holes (perforated).
• Put the sanding paper close to the sanding pad (1).
• Place the sanding paper so its holes (a) match with the holes on the
sanding pad (1).
• Press the sanding paper against the sanding pad (1).
• Make sure that the holes on the sanding paper and sanding pad fully
match; it ensures optimal conditions for dust extraction.
• To remove sanding paper, lift edge of it on one side and pull (fig. A).
INSTALLATION OF WORKING TOOLS
• Remove working tool if already installed.
• Use hexagonal key to unscrew the fixing screw (6), remove washer and
remove the working tool.
• Place working tool in the tool holder, make sure to close latch joint of the
tool and tool holder.
• You can place working tools onto the tool holder in any latching position
(fig. B) to allow for operation most comfortable and safe for the user.
• Working tool should be installed with bend pointing down.
• Place washer and tighten the screw (6) to install working tool.
Check that the tool is installed properly. Improperly or inaccurately
installed working tools can slip during operation and cause risk for the
user.
DUST EXTRACTION
WARNING! Dust of some materials may be hazardous to health, like
paint coatings with lead additives, some types of wood e.g. oak or
beech or materials with asbestos. Therefore, we recommend use of
external dust extraction systems, good workplace ventilation and use
of dust-mask with particle filter.
The tool is equipped with dust extraction add-on, which should be
connected to external dust extractor after installation, e.g. vacuum cleaner
designed for the type of produced dust.
• Remove working tool if already installed.
• Install dust extraction add-on (5) and fix with clamp (4).
• Connect suction hose, e.g. vacuum cleaner to the adaptor (3) of the dust
extraction add-on (5).
• Install working tool in the tool holder.
OPERATION / SETTINGS
SWITCHING ON / SWITCHING OFF
The mains voltage must match the voltage on the label of the tool.
Switching on – slide the switch (2) forward to position I (fig. C).
Switching off – slide the switch (2) backward to position O.
WARNING! Do not cover holes for motor ventilation in the tool body.
PRINCIPLES OF OPERATION
Oscillation frequency 20000 rpm at 2.8° angle allows to work precisely in
small areas and corners with the power tool.
SAWING AND CUTTING
Use only undamaged working tools in good technical condition. When
sawing or cutting wood, fibre board, wood-based materials etc. make
sure they do not contain foreign objects like nails, bolts etc before
starting the task. Remove foreign objects or use proper blade for
removal. You can make plunge cuts only in soft materials like wood,
gypsum boards and alike. Cutting ceramic tiles causes faster wear of
working tool.
SANDING
Working efficiency in surface sanding depends mainly on type and quality
of sanding paper and pressure applied for processing. Overpressure does
not make sanding more efficient, it only causes faster wear of sanding paper
and may cause overheating of the power tool. Apply moderate and uniform
pressure.
You can use tip or edge of the sanding pad to sand corners or edges in hardly
accessible places.
Proceed with sanding tasks only with dust extraction system
connected. Do not use paper previously used for metal polishing for
processing material of other type
OPERATION AND MAINTENANCE
Unplug the power cord from mains socket before commencing any
activities related to installation, adjustment, repair or maintenance.
MAINTENANCE AND STORAGE
• Always keep the tool clean.
• Do not use water or any other liquid for cleaning.
• Use a brush or a dry piece of cloth to clean the power tool.
• Clean working tools with a wire brush.
• Clean ventilation holes regularly to prevent motor overheating.
• In case of excessive commutator sparking, have the technical condition
of carbon brushes of the motor checked by a qualified person.
• Store the tool in a dry place, beyond reach of children.
REPLACEMENT OF CARBON BRUSHES
Replace immediately worn out (shorter than 5 mm), burnt or cracked
motor carbon brushes. Always replace both carbon brushes at a time.
Entrust replacement of carbon brushes only to a qualified person.
Only original parts should be used.
All defects should be repaired by service workshop authorized by the
manufacturer.
TECHNICAL PARAMETERS
RATED PARAMETERS
Multi Purpose Tool
Parameter
Supply voltage
Input current frequency
Rated power
Idle oscillation speed
Oscillation angle
Pad dimensions
Protection class
Weight
Year of production
NOISE LEVEL AND VIBRATION PARAMETERS
Sound pressure: Lp
= 84 dB(A); K = 3 dB(A) Sound power: Lw
A
dB(A) Vibration acceleration: ah = 9 m/s
5
Value
230 V AC
50 Hz
180 W
20000 min
-1
2,8°
80 x 80 x 80 mm
II
1,35 kg
2021
= 95 dB(A) ; K = 3
A
; K= 1.5 m/s
2
2
Publicidad
Tabla de contenido
