Baxi PBM-i 20 Manual Del Usuario página 149

SYSTEM CONFIGURATION
System number 3
Parameter configuration
Description
Select system configuration
System type (table 1)
Mixing valve ZONE 1
Type of mixing valve 0= 3-position 1= 0-10V
3-position valve travel time
HEATING compensation curve ZONE 1
Enable compensation curve 0= Disabled 1= Enabled
heating compensation curve number
Enable room temperature influence
0= Disabled 1= Enabled
Room Authority
MINIMUM outlet set point limit for curve
MAXIMUM outlet set point limit for curve
COOLING compensation curve of ZONE 1
Enable compensation curve 0= Disabled 1= Enabled
Maximum outlet temperature set point limit in cooling mode (Tm1)
Minimum outside temperature corresponding to max. outlet
temperature (Te1)
Minimum outlet temperature set point limit in cooling mode (Tm2)
Maximum outside temperature corresponding to min. outlet
temperature (Te2)
HUMIDITY CONTROL ZONE 1
Enable compensation for room humidity, ZONE LT1
0= Disabled 1= Enabled
Room relative humidity value to start increasing water outlet temperature
set point
Maximum outlet temperature hysteresis corresponding to 100%
relative humidity
Enable contact kA11 as DEhUMIDIFIER (The contact closes and the
dehumidifier is activated when the humidity measured by the probe on
the A5 room controller exceeds the value set for parameter 0172)
HEATING compensation curve ZONE 2
Enable compensation curve 0= Disabled 1= Enabled
Compensation curve number
Enable room temperature influence
0= Disabled
1= Enabled
Room Authority
MINIMUM outlet set point limit curve
MAXIMUM outlet set point limit curve
COOLING compensation curve ZONE 2
Enable compensation curve 0= Disabled 1= Enabled
Maximum outlet temperature set point limit in cooling mode (Tm1)
Minimum outside temperature corresponding to max. outlet
temperature (Te1)
Minimum outlet temperature set point limit in cooling mode (Tm2)
Maximum outside temperature corresponding to min. outlet
temperature (Te2)
ZONE 2 room controller address setting
The SYSTEM compensation curve in hEATING mode, parameter 0159, must be set so as to reach an outlet temperature suitable for the high
temperature zone with radiators. The mixed zone is managed according to the compensation curve set for parameter 0174.
The room unit (A5), supplied as standard with the heat pump, controls the room temperature in zone 1, with radiant panels, the additional room
unit (accessory) controls the room temperature in zone 2, with radiators or fan coils.
Enable contact hL1 as secondary circuit pump:
0= Alarm signal
1= Dehumidifier
3= Secondary circuit pump
* obligatory values for the present configuration
Parameter
Menu Default
no.
Mn01 0101
Mn01 012T
Mn01 013B 150
Mn01 0167
Mn01 0174 0,7
Mn01 0178
Mn01 0179 30
Mn01 0180 23
Mn01 0181 45
Mn01 0169
Mn01 0132 20
Mn01 0133 23
Mn01 0134 18
Mn01 0135 36
Mn01 0171
Mn01 0172 70
Mn01 0173 15
Mn01 011B
Mn01 0152
Mn01 0159
Mn01 0163
Mn01 0164 30
Mn01 0165 30
Mn01 0166 48
Mn01 0154
Mn01 0128 20
Mn01 0129 23
Mn01 0130 18
Mn01 0131 36
addr
Mn01 015A
U I A
Write set value UOM
0 3*
0
sec
0
0
°C
°C
0
°C
°C
°C
°C
0
°C
0 1*
0
1
0
°C
°C
0
°C
°C
°C
°C
1 11*
0 3*
EN PBM 20÷40
-
%
%
-
-
-
%
-
69