List Of Parameters - Baxi PBM-i 20 Manual Del Usuario

LIST OF PARAMETERS

Description
Enable domestic hot water set point: 0 = Economy, 1 = Comfort
Domestic hot water Economy set point
Domestic hot water Comfort set point
User password
Enable remote contact: 0= remote contact enabled, 1= remote contact disabled (selection from keypad only)
Automatic mode changeover set point in hEATING
Automatic mode changeover differential in hEATING
Automatic mode changeover set point in COOLING
Automatic mode changeover differential in COOLING
Type of outlet heater operation: 0 = Supplementary , 1 = Replacement
Type of boiler operation: 0 = Supplementary , 1 = Replacement
kA11 contact configuration: 0 = Domestic hot water recirculation, 1 = Dehumidifier
SA7 input configuration: 1= Switch
Ratio between system and room: 0 = Unit in room mode, 1 = Unit in independent mode
Installer password
Fixed water outlet temperature set point in hEATING zone LT3
Enable compensation curve in COOLING zone LT3: 0 = Disabled, 1= Enabled
Fixed water outlet temperature set point in COOLING zone LT3
Maximum outlet temperature set point limit in cooling mode (Tm1)
Minimum outside temperature corresponding to max. outlet temperature (Te1)
Zone LT3 compensation curve number
Enable room temperature influence on LT3 0= Disabled 1= Enabled
LT3 Room Authority
MINIMUM outlet set point limit for compensation curve in zone LT3
MAXIMUM outlet set point limit for compensation curve in zone LT3
Maximum outlet temperature set point limit in cooling mode (Tm1)
Minimum outside temperature corresponding to max. outlet temperature (Te1)
Minimum outlet set point limit in cooling mode (Tm2)
Minimum outside temperature corresponding to min. outlet temperature (Te2)
Enable compensation for room humidity, ZONE LT3: 0= Disabled , 1= Enabled
Room relative humidity value to start increasing water outlet temperature set point, ZONE LT3
Maximum outlet temperature hysteresis corresponding to 100% relative humidity
Minimum outlet temperature set point limit in cooling mode (Tm2)
Maximum outside temperature corresponding to min. outlet temperature (Te2)
Maximum outlet temperature set point limit in cooling mode (Tm1)
Minimum outside temperature corresponding to max. outlet temperature (Te1)
Minimum outlet temperature set point limit in cooling mode (Tm2)
Maximum outside temperature corresponding to min. outlet temperature (Te2)
Maximum outlet temperature set point limit in cooling mode (Tm1)
Minimum outside temperature corresponding to max. outlet temperature (Te1)
Minimum outlet temperature set point limit in cooling mode (Tm2)
Maximum outside temperature corresponding to min. outlet temperature (Te2)
Inside temperature to enable frost protection
Outside air temperature for frost protection
Activation of system pump operation at intervals: 0= system pump always on, 1=system pump operation at intervals
System pump curve number: 1= Curve 1, 2= Curve 2, 3= Curve 3, 4= Curve 4
System pump operating time in sniffing mode
System pump off time between one sniffing cycle and the next
Enable SYSTEM compensation curve 0= Disabled 1= Enabled
Fixed water outlet temperature set point in hEATING
Enable SYSTEM compensation curve: 0= Disabled, 1= Enabled
Fixed water outlet temperature set point in COOLING
Enable compensation for room humidity, SYSTEM: 0= Disabled , 1= Enabled
Room relative humidity value to start increasing water outlet temperature set point, SYSTEM
Maximum outlet temperature hysteresis corresponding to 100% relative humidity
SYSTEM compensation curve number
Enable contact as: 0= Alarm signal, 1= Dehumidifier, 3= Secondary circuit pump
Enable contact as: 0 = System pump, 1= System outlet electric heater, 1st stage, 4= Unit operating mode signal (cooling/heating)
Enable contact as: 0 = DhW recirculation, 1= Dehumidifier, 2= Secondary circuit pump, 3= Unit operating mode signal
(cooling/heating)
Enable the contact as: 0=Reduced electricity rate, 1=Stop operation due to excess power consumption
Enable compensation curve in hEATING zone LT3 0= Disabled 1= Enabled
Enable room temperature influence on SYSTEM 0= Disabled 1= Enabled
SYSTEM Room Authority
Minimum set point limit for SYSTEM curve
Maximum set point limit for SYSTEM curve
Enable compensation curve in hEATING zone LT1 0 = Disabled, 1 = Enabled
Fixed water outlet temperature set point in hEATING zone LT1
Enable compensation curve in COOLING zone LT1: 0 = Disabled, 1 = Enabled
74 PBM 20÷40 EN
U I A U I A
Menu Parameter no. UOM
Mn00 0015
Mn00 0022 °C
Mn00 0023 °C
Mn00 0036
Mn01 0100
Mn01 0106 °C
Mn01 0107 °C
Mn01 0108 °C
Mn01 0109 °C
Mn01 010G
Mn01 010h
Mn01 011B
Mn01 011C
Mn01 011D
Mn01 011G
Mn01 011R
Mn01 011T
Mn01 011U °C
Mn01 0128 °C
Mn01 0129 °C
Mn01 012A
Mn01 012D
Mn01 012E %
Mn01 012F °C
Mn01 012G °C
Mn01 012h °C
Mn01 012J °C
Mn01 012L °C
Mn01 012M °C
Mn01 012N
Mn01 012P %
Mn01 012R °C
Mn01 0130 °C
Mn01 0131 °C
Mn01 0132 °C
Mn01 0133 °C
Mn01 0134 °C
Mn01 0135 °C
Mn01 0136 °C
Mn01 0137 °C
Mn01 0138 °C
Mn01 0139 °C
Mn01 0140 °C
Mn01 0141 °C
Mn01 0143
Mn01 0146
Mn01 0147
Mn01 0148
Mn01 0152
Mn01 0153 °C
Mn01 0154
Mn01 0155 °C
Mn01 0156
Mn01 0157 %
Mn01 0158 °C
Mn01 0159
Mn01 015A
Mn01 015B
Mn01 015C
Mn01 015D
Mn01 015E
Mn01 0163
Mn01 0164 %
Mn01 0165 °C
Mn01 0166 °C
Mn01 0167
Mn01 0168
Mn01 0169