Maintenance And Service - Bosch GCM 10 PROFESSIONAL Instrucciones De Servicio

GCM10_ASIA.book Seite 12 Dienstag, 18. September 2007 9:40 09
Checking and Adjusting Basic Adjustment
Before all work on the machine, pull the power
plug.
To ensure precise cuts, the basic adjustment must be
checked and adjusted as necessary after intensive us
age.
Bevel Angle 33,9° (Vertical)
Place the machine in the working position.
Rotate the saw table 15 to the detent 14 for 0°. Loos
en the clamping lever 30 and pull the fence extension
22 completely out.
Loosen the clamping handle 32 and press the setting
knob 31 completely in. Swing the tool arm with the
handle 1 until the pin 24 rests against the stop bolt 23.
Checking: (see Figure )
S1
Place a combination square set to 33,9° on the saw
table 15. The leg of the square must be flush with the
saw blade over its entire length.
Adjusting: (see Figure )
S2
Loosen the locking nut of the stop bolt 23 with the
open ended wrench 36 (12 mm) provided. Turn the
stop bolt either in or out until the leg of the square is
flush with the saw blade over its entire length.
Retighten the clamping handle 32. Then retighten the
locking nut of the stop screw 23.

5 MAINTENANCE AND SERVICE

Maintenance
Before all work on the machine, pull the power
plug.
Always keep the machine and the ventilation slits clean
for efficient and safe working.
The swinging guard must always be able to move free
ly and close by itself. Therefore, always keep the area
around the swinging guard clean.
Remove dust and chips by blowing out with com
pressed air or with a brush.
Clean the roller 25 regularly.
Should the tool fail in spite of careful manufacturing
and testing procedures, have the repairs performed by
an authorized customer service location for Bosch
Electro Tools.
For inquiries and spare parts ordering, please include
the 10 digit order number on the nameplate of the
tool.
1 619 P04 359 • (2007.09)
Fence
Place the electro tool in the transport position.
Rotate the saw table 15 to the detent 14 for 0°. Loos
en the clamping lever 30 and pull the fence extension
22 completely out.
Checking: (see Figure
Set the combination square to 90° and place it on the
saw table 15. The square must be flush with the fence
6 over its entire length.
Adjusting: (see Figure
Loosen all three socket head screws 35 with the Allen
key 21 (6 mm) provided. Rotate the fence 6 until the
square is flush with the fence over its entire length. Re
tighten the socket head screws.
Accessories
Saw blade 254 x 30 mm, 40 teeth. . . 2 608 640 438
Saw blade 254 x 25,4 mm, 40 teeth . 2 608 640 459
Saw blade 254 x 16 mm, 40 teeth. . . 2 608 640 466
Saw blade 254 x 25,4 mm, 120 teeth 2 608 640 465
Quick action clamp . . . . . . . . . . . . . . 2 608 040 205
Table insert . . . . . . . . . . . . . . . . . . . . 2 607 960 014
Dust bag . . . . . . . . . . . . . . . . . . . . . . 2 605 411 187
Extension hoop (356 mm) . . . . . . . . . 2 607 001 911
Angle adapter for dust bag . . . . . . . . 2 608 601 171
Vacuuming adapter for 35 mm hose . 2 605 702 022
Carrying bag . . . . . . . . . . . . . . . . . . . 2 605 435 019
Disposal
Tool, accessories and packaging should be sorted for
environment friendly recycling.
The plastic components are labeled for categorized re
cycling.
English–12
)
T1
)
T2