EINHELL GE-LM 36/4in1 Li Manual Del Usuario página 32

low pressure.
•
We recommend cleaning the equipment
immediately each time after use.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use cleaning
agents or solvents; these may be aggressive
to the plastic parts in the equipment. Ensure
that no water can get into the interior of the
equipment. The ingress of water into an
electric power tool increases the risk of an
electric shock.
General information on maintenance
There are no other parts inside the equipment
which require maintenance.
To keep the tool in good working order, carry
out regular maintenance in accordance with the
following instructions. Use only the accessories
and spare parts approved by the manufacturer,
Details can be found in section 8.6 "Ordering
spare parts". The use of non-approved
accessories or spare parts can result in very
serious injuries.
Maintenance of the cordless string trimmer /
brush cutter
8.1 Replacing the string spool (Fig. 48-49)
Danger! Remove the batteries!
1. Press the string spool housing together at the
ribbed points marked an arrow and remove
the spool cover.
2. Take out the empty string spool and the
pressure spring.
3. Thread the end of the string from the new
string spool through the eyelet (Item 53) of the
spool cover and allow approx.
5.11 in. (130 mm) of string to project. Insert
the pressure spring (Item 54) in the string
spool.
4. Press the spool cover back into the string
spool housing.
8.2 Replacing the string (Fig. 48, 50, 51)
Danger! Remove the batteries!
1. Press the string spool housing together at the
ribbed points marked H and remove the spool
cover.
2. Take out the empty string spool and the
pressure spring.
3. Remove any remaining string.
4. Insert the new string into the string holder
inside the spool.
5. Keeping the string under tension, wind it up
Anl_GE_LM_36_4in1_Li_SPK7_USA.indb 32 Anl_GE_LM_36_4in1_Li_SPK7_USA.indb 32
EN
counter-clockwise.
6. Hook approx. 5.9 in. (150 mm) of the end of
the string into one of the string holders on the
edge of the spool.
7. Thread the end of the string from the new
string spool through the eyelet (Item 53) in the
spool cover. Insert the pressure spring (Item
54) in the string spool.
8. Tug the string sharply to release it from the
string holder.
9. Press the spool cover back into the string
spool housing.
When you start the equipment again the string will
be cut to the perfect length automatically.
Important! Bits of the nylon string could
cause injury when fl ung out.
8.3 Sharpening the string blade (Fig. 9)
The string blade (Item 41) can become blunt
over time. When you notice this, undo the screws
holding the string blade on the guard hood. Clamp
the blade in a vise. Sharpen the blade with a fl at
fi le and make sure that the angle of the cutting
edge is not altered in the process. File in one
direction only.
8.4 Maintenance of the telescoping pole
chain saw
Use only saw chains and cutter rails approved by
the manufacturer. These are listed in section 4
"Technical data" or are available as accessories
(see section 8.6 "Ordering spare parts"). The use
of spare parts which are not approved by the
manufacturer could result in very serious injuries.
Replacing the saw chain and cutter rail
The cutter rail needs to be replaced if the guide
groove of the cutter rail is worn. Proceed as
described in the section "Cutter rail and saw
chain".
Checking the automatic chain lubrication
You should check the operation of the automatic
chain lubrication system on a regular basis
in order to guard against overheating and the
damage this can cause to the bar and the
chain. Point the tip of the cutter rail at a smooth
surface (a board or a cut tree face) and allow
the telescoping pole chain saw to run. If you see
a growing oil stain on the smooth surface, the
automatic chain lubrication system is working
properly. If no clear oil trace is evident then
please refer to the corresponding instructions
in "Troubleshooting guide"! If the information
- 32 -
29.09.2021 09:33:54 29.09.2021 09:33:54