Metabo HPT C 10FSH C 10FSHS Instrucciones De Seguridad Y Manual De Instrucciones página 23

Fence
Cutting method of crown molding without tilting the saw blade.
Crown molding Stopper (R)
Crown molding Vise Ass'y
(optional accessories)
(optional accessories)
6mm Knob
Bolt
6mm Knob Bolt
Crown molding Stopper (L)
6mm Wing Bolt
(optional accessories)
Fig. 44
Crown molding Vise Ass'y
(optional accessories)
6mm Knob Bolt
V-Groove
Groove
Fence
6mm wing bolt
Crown molding
Crown molding Stopper (L)
Crown molding Stopper (R)
(optional accessories)
Fig. 45
WARNING:
Always fi rmly clamp or vise to secure the crown molding to the fence; otherwise
the crown molding might be thrust from the table and cause bodily harm.
Do not bevel cutting. The main body or saw blade may contact the sub fence,
resulting in an injury.
CAUTION:
Always confi rm that the motor head (see Fig. 1) does not contact the crown molding
vise ass'y when it is lowered for cutting. If there is any danger that it may do so,
loosen the 6mm knob bolt and move the crown molding vise ass'y to a position
where it will not contact the saw blade.
Position crown molding with its WALL CONTACT EDGE against the guide fence and its CEILING CONTACT
EDGE against the crown molding Stoppers as shown in Fig. 45.
Adjust the crown molding Stoppers according to the size of the crown molding.
Tighten the 6mm wing bolt to secure the crown molding Stoppers.
Refer to the lower table for the miter angle.
For inside corner
For outside corner
Use the sub fence (A) (optional accessories) to secure the crown molding more fi rmly. (see Fig. 15)
Table on Base
Fig. 42
(1) Crown molding Stopper (L) and (R) (optional accessories)
allow easier cuts of crown molding without tilting the saw
blade. Install them in the base both-sides side to be shown in
Fig. 44. After inserting Tighten the 6mm knob bolts to secure
the crown molding Stoppers.
[Optional accessories used]
• Crown molding Vise Ass'y (Include Crown molding Stopper
(L))
• Crown molding Stopper (L)
• Crown molding Stopper (R)
(2) The crown molding vise (B) (Optional accessory) can be
mounted on either the left fence (Fence (B)) or the right fence
(Fence (A)). It can unite with the slope of the crown molding
and vice can be pressed down.
Then turn the upper knob, as necessary, to securely attach the
Knob
crown molding in position. To raise or lower the vise assembly,
fi rst loosen the 6mm knob bolt. As shown in Fig. 45, the vise
shaft has three locking grooves into which the tip of the 6mm
wing bolt is designed to fi t in order to lock the screw holder in
the desired position.
To ensure that the tip of the 6mm wing bolt is properly aligned
with the desired locking groove on the vise shaft, simply align
the upper surface of the fence to either of three v-grooves
on the vise shaft surface or to the lower surface of the screw
holder.
Therefore, the vise assembly can be attached in either of three
positions to ensure proper height adjustment.
After adjusting the height, fi rmly tighten the 6mm wing bolt;
then turn the upper knob, as necessary, to securely attach the
the crown molding in position. (see Fig. 45)
Position in Fig. 34
1
2
3
4
Fence
Table on Base
Fig. 43
Miter angle
Right 45° Save the right side of blade
Save the left side of blade
Left 45°
Save the right side of blade
Right 45° Save the left side of blade
English
Finished piece
23