Replacement Parts - Metabo HPT C 10FSH C 10FSHS Instrucciones De Seguridad Y Manual De Instrucciones

27. Ensure before each cut that the machine is stable.
28. If the saw blade should become jammed, switch the machine off
and hold the workpiece until the saw blade comes to a complete
stop. To prevent kickback, the workpiece may not be moved until
after the machine has come to a complete stop.
Correct the cause for the jamming of the saw blade before
restarting the machine.
29. Use only saw blades that are marked with a maximum permitted
speed equal or higher than the no-load speed marked on the
POWER TOOL.
30. Use only a saw blade diameter in accordance with the markings
on the POWER TOOL.
31. Replace the table insert when worn.
DON'Ts
NEVER VIOLATE THE FOLLOWING RULES TO
ASSURE SAFE USE OF THIS TOOL:
1. Never operate the POWER TOOL unless you fully understand
the operating instructions contained in this Manual.
2. Never leave the POWER TOOL unattended without fi rst
unplugging the power cord.
3. Never operate the POWER TOOL when you are tired, after you
have taken any medications, or have consumed any alcoholic
beverages.
4. Never use the POWER TOOL for applications not specifi ed in
the instruction manual.
5. Never operate the tool while wearing loose clothing, a necktie or
jewelry, or while your hair is uncovered, to protect against getting
caught in the moving machinery.
6. Never reach around the saw blade.
7. Never touch any moving parts, including the blade, while the
saw is in use.
8. Never remove any safety devices or blade guards; use of the
tool without them would be hazardous.
9. Never lock the lower guard; always confi rm that it slides smoothly
before using the tool.
10. Never damage the power cord of the tool.
11. Never attempt to move a plugged-in POWER TOOL while your
fi nger is on the starting switch.
12. Never use the POWER TOOL if the starting switch does not turn
on and off properly.
13. Never use the POWER TOOL if the plastic housing or the handle
is cracked or deformed.
14. Never use the POWER TOOL near fl ammable liquids or gases
because sparking can cause an explosion.
15. Never clean plastic components with solvents because the
plastic may dissolve.
16. Never operate the saw unless all the blade guards are in place.
17. Never raise the saw blade from the workpiece until it has fi rst
come to a complete stop.
18. When slide cutting, never pull the handle toward the operator,
since this could cause the saw blade to kick up from the
workpiece. Always push the handle away from the operator in a
single, smooth motion.
19. Never place your limbs inside of the line next to warning sign
" " while the tool is being operated. This may cause hazardous
conditions.
20. Never use abrasive type blades on this saw.
21. Never expose to rain or use in damp locations.
22. Never cut ferrous metals or masonry.
23. Do not stand in a line with the saw blade In front of the machine.
Always stand aside of the saw blade. This protects your body
against possible kickback. Keep hands, fi ngers and arms away
from the rotating saw blade.
24. Do not cross your arms when operating the tool arm.
WARNING
FOR YOUR OWN SAFETY READ THIS INSTRUCTION
MANUAL BEFORE OPERATING
COMPOUND MITER SAW
1. Always wear eye protection when using the slide compound
miter saw.
2. Always keep hands out of the path of the saw blade.
3. Never operate the saw without the guards in place.
4. Never perform any freehand operation with the slide compound
miter saw.
5. Never reach around the saw blade.
6. Always turn off tool and wait for saw blade to stop before moving
workpiece or changing settings.
7. Always disconnect power before changing blade or servicing.
8. Saw blade diameter is 10" (255mm).
9. No load speed is 5000/min.
10. To reduce the risk of injury, return carriage to the full rear position
after each crosscut operation.

REPLACEMENT PARTS

When servicing use only identical replacement parts.
Repairs should be conducted only by a metabo HPT authorized
service center.
English
THE SLIDE
5