Baby auto biro fix Manual De Uso página 12

6. installinG tHe car seat. GrouP 1
GROUP 1 only. From 9 months to 4 years
notice
approx. (9-18 kg)
1. Ensure the seat is not in a reclined position (the indicator should be in
position 1) and is ready to install in forward position (Group 1) as shown
in fig. 6.1. Pull the lever (G)
position 1 without releasing the lever. if it is necessary swivel the seat
180º to place the seat in the direction of travel (fig. 6.1.A). Release the
lever when the seat is in the desired position.
2. Locate the isoclick Fix® arms
3. Place the child safety seat in the back seat of the vehicle facing in the
direction of travel.
4. Hold the safety seat with both hands and insert the two isoclick Fix®
arms (n) firmly into the vehicle´s isofix anchoring points until they
fasten with a click on both sides. The red button will change to green on
both sides (fig. 6.3).
5. Shake the seat to check that it is correctly anchored to the vehicle's
iSoFiX points.
6. Pass the vehicle seat belt through the slot on the back of the safety
(M)
seat (fig. 6.4) until it appears at the exit. Buckle the vehicle seat
belt until you hear a click (fig. 6.5).
7. Take up the slack by pulling the abdominal section of the belt until it is
as tight-fitting as possible (fig 6.6).
8. Ensure the straps are not twisted at any point.
uninstalling the isoclick fix® arms
1. To release the isoclick Fix® arms, pull the button on the anchors to
unlock them until the indicator turns from green to red color. This
will release the child seat (fig. 6.7 and 6.8).
7. PlacinG tHe cHild in tHe seat. GrouP 1
To seat the child correctly follow the steps described in chapter 4.
8. reMoVinG tHe Harness and safety buckle
1. removing the 5 point harness and the safety buckle
1. Loosen the harness straps by pulling them gently while pressing the
22
forward and adjust the angle of recline to
(n) in the base of the seat (fig. 6.2).
harness adjustment button (e)
2. Loosen the harness straps from the back of the seat, freeing them
from the harness connector (i). Repeat the operation with the shoulder
straps connector (o) (fig. 8.2 and 8.3).
3. Pull the harness straps from the front to free them from the seat back
(fig. 8.4).
4. Take off the safety buckle (d), passing the retention plate through the
seat base slots.
2. removing the fabric cover
1. Take off the headrest fabric cover (fig.8.5).
2. Take off the seat cover unbuttoning the brackets that secure the cover
to the plastic base. Pull the shoulder straps
eyelets (fig.8.6).
3. Take off the fabric cover from the car seat.
9. installinG tHe cHild seat. GrouP 2
notice
GROUP 2 only. From 4 to 6 years approx. (15-25 Kg)
before installing the seat for Group 2, the seat harnesses (b), harness
( c) (d)
protectors and buckle must be removed. Please, for this, follow
chapter 8.1.
1. Ensure the seat is not in a reclined position (the indicator should be in
position 1) and is ready to install in forward position (Group 1) as shown in
fig. 6.1. Pull the lever (G) forward and adjust the angle of recline to position
1 without releasing the lever. if it is necessary swivel the seat 180º to place
the seat in the direction of travel (fig. 6.1.A). Release the lever when the
seat is in the desired position (fig. 6.1)
2. Place the child safety seat in the back seat of the vehicle facing in the
direction of travel (fig. 6.3).
10. PlacinG tHe cHild in tHe seat. GrouP 2
1. According to the child's height the headrest can be adjusted up or down.
Place your hand on the headrest height regulator and pull while pulling the
seat down with the other hand so it does not move (9.1).
2. Place the child safety seat in the back seat of the vehicle facing in the
direction of travel.
(fig.8.1)
(b) through the base cover
23