Technical Specification; Double Insulation - Narex ASR 18-S Instrucciones De Uso Originales

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 24

Technical specification

Cordless impact wrench:
Model
Voltage
Idle speed:
Number of strokes:
Tightening moment max.:
Scope of application:
Metric screws
Wood screws - dia. max.:
Drilling - dia. max.:
Spindle
Weight w/o accumulators
Charger:
Model
Input voltage
Frequency
Power input
Output voltage
Charging current
Charge time
Weight
Class of protection
Accumulator:
Model
Voltage
Cell type
Capacity
Temperature of charging
Charge time
Monitor. of the temp.of charging
Weight
* Depending on model and capacity of the accumulator to be charged!
Description:
1 ...........Accumulator
2 ...........Accumulator clamp
3 ...........Switching–in push button with speed control
4 ...........Reversing switch
5 ...........Spindle - ½" square
6 ...........Workplace LED lighting
7 ...........Accumulator state indication panel
8a .........Indication switch
8b .........Accumulator state indicator
9 ...........LED signal lights
10 .........Charger
11 .........Vent holes of the accumulator air cooling system
Zobrazené anebo popsané příslušenství nemusí patřit do objemu
dodávky.
Scope of use
The cordless impact nut runners are specified for screwing and the
cordless impact nut runner ASR 18-S even for drilling into wood,
metal and plastics.
ASR 18-S
18.0 V
0–2 000 rpm
0–3 000 rpm
400 Nm
M12–M18
8 mm
into metal
8 mm
into wood
18 mm
½" square
1.25 kg
AN-UNI C
110–240 V
50–60 Hz
80–100 W
16.6–20.7 V
4 A
ca 25–45 min*
0.7 kg
II /
AP 18 LE
18.0 V
Li-Ion
1.5 Ah
0–45 °C
ca 25 min
thermistor
0.52 kg

Double insulation

To ensure maximum safety of the user our tools are designed and
built to satisfy applicable European standards (EN standards). Tools
with double insulation are marked by the international symbol of
a double square. These tools must not be grounded and a two-wire
cable is sufficient to supply them with power. Tools are shielded in
accordance with EN 55014.
Charging battery pack instructions
1. Make sure that circuit voltage is the same as than shown on
the charger specification plate. Connect the charger  (10) to
power source. Red LED signal light should light up  (9). This
indicates the charger is ready to being charging. If the red LID
light is not on, check connection to the power source. If the
power source is OK, transport the charger into the authorized
service workshop!
2. Position the accumulator/battery pack (1) into the charger as
far as the stop, see the Fig.
3. The red light will go out and the green light begins to blink,
indicating that the battery pack is receiving a "Fast Charge".
4. After approximately 25–45 minutes (depending on battery
pack type) the battery pack is fully charged. The green light
will become steady.
5. Press the accumulator clamps (2) on both sides and by pull the ac-
cumulator out of the charger. If you do not want to charge another
accumulator, disconnect the charger from the power source.
English
ASR 18 HT-S
18.0 V
0–1 700 rpm
0–2 000 rpm
800 Nm
M12–M24
½" square
2.4 kg
AP 18 LP
18.0 V
Li-Ion
3.0 Ah
0–45 °C
ca 45 min
thermistor
0.78 kg
19

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Asr 18 ht-s

Tabla de contenido