Cameo SERUM Manual De Usuario página 15

8
EYELET FOR SAFETY CABLE / ÖSE FÜR SICHERUNGSSEIL / OEILLET POUR ÉLINGUE DE SÉCURITÉ / ARGOLLA PARA CABLE DE
SEGURIDAD / UCHWYT NA LINĘ ZABEZPIECZAJĄCĄ / OCCHIELLO PER CORDA DI SICUREZZA
EN
Overhead installation should only be carried out by trained personnel. The spot must be secured with an appropriate safety cable to the safety
eyelet to prevent falling.
DE
Überkopfmontage darf nur von dafür ausgebildetem Personal durchgeführt werden. Der Scheinwerfer ist dabei mit einem geeigneten
Sicherungsseil an der Sicherungsöse gegen Herabfallen zu sichern.
FR
Le montage en hauteur, au-dessus de la tête des spectateurs, ne doit être effectué que par un personnel qualifié. Le projecteur doit donc être
sécurisé par passage d'une élingue de sécurité dans l'œillet de sécurité, afin d'éviter tout risque de chute.
ES
El montaje suspendido sólo puede realizarse por personal experimentado. Para evitar cualquier riesgo de caída, el foco debe asegurarse
introduciendo un cable de seguridad apropiado a través de la argolla de seguridad.
PL
Montaż nad głową może być wykonywany wyłącznie przez odpowiednio przeszkolony personel. Reflektor należy przy montażu zabezpieczyć
przed upadkiem za pomocą odpowiedniej liny zabezpieczającej, którą przewleka się przez uchwyt bezpieczeństwa.
IT
Il montaggio sopratesta può essere eseguito esclusivamente da personale qualificato che dovrà inoltre provvedere a fissare il faro all'occhiello
di sicurezza con un cavo di sicurezza adatto per prevenirne la caduta.
OPERATION / BEDIENUNG / UTILISATION / OPERACIÓN / OBSŁUGA / UTILIZZO
EN
A few seconds after connecting to the power supply, the effects projector is ready for operation and the operating mode that was previously
selected is activated. The effects beam automatically switches to the DMX operating mode when a DMX signal is present at the DMX input. If the
DMX signal is interrupted, the mode that was previously selected (DMX, Automatic control, Music control) is automatically activated.
SELECTING THE DMX START ADDRESS
Press the MODE button repeatedly until "Add" appears on the display. Press ENTER, and adjust the DMX start address as desired by using the UP
and DOWN buttons (A001 - A512). Confirm the input with ENTER. The synchronous control of multiple spotlights (same model) through a DMX control
unit (e.g. DMX console) can be achieved by assigning the spotlights to an identical DMX start address and DMX mode and connecting them using
DMX cables.
-> ENTER->
SETTING THE DMX MODE
Press the MODE button repeatedly until "CHmd" appears on the display. Press the ENTER button and select one of the 3 available DMX modes using
the UP and DOWN buttons (CH02, CH04, CH06). Confirm the input with ENTER.
-> ENTER->
AUTOMATIC CONTROL MODE (AUTO)
Press the MODE button repeatedly until "AUTO" appears on the display. Now press ENTER to activate the automatic control and to display the auto
program currently set (Pr00 - Pr07). One of the 8 auto programs can now be selected by using the UP and DOWN buttons. After confirming by press-
ing the ENTER button, you can now select the speed at which the selected program runs by using the UP and DOWN buttons (the display shows:
SP01 = minimum speed, SP99 = maximum speed). Confirm with ENTER.
-> ENTER-> UP/DOWN
MUSIC CONTROL MODE (SOUND)
Press the MODE button repeatedly until "SOUn" appears on the display. Now press ENTER to activate the Music control mode and display the cur-
rently set program (Pr00 - Pr07). One of the 8 sound programs can now be selected by using the UP and DOWN buttons. After confirming by pressing
ENTER, you can now select the sensitivity with which the device responds to sounds (bass pulses) by using the UP and DOWN buttons (the display
shows: SU00 = minimum sensitivity, SU99 = maximum sensitivity) Confirm with ENTER.
-> ENTER-> UP/DOWN
SLAVE MODE
The slave operating mode of the hybrid LED effect is automatically activated (slave unit) as soon as another hybrid LED effect of the same model is
operated in one of the standalone modes (AUTO, SOUND) and is connected via a DMX cable, and if there is no DMX signal from a DMX controller at
the DMX interfaces of both hybrid LED effects.
UP/DOWN
UP/DOWN
-> ENTER
<- MODE
-> ENTER ->
UP/DOWN
<- MODE
-> ENTER ->
UP/DOWN
<- MODE
-> ENTER
<- MODE
-> ENTER
<- MODE
-> ENTER
<- MODE
15