Setup - Titan SPEEFLO PowrLiner 2850 Manual Del Propietário

Setup

Perform the following procedure before starting the engine of a gas-
powered line striper.
NOTE: The PL2850 comes in two versions, a one-gun
version and a two-gun version. All information
given in this manual applies to both units, except
where noted.
1. Ensure that the siphon hose and the return hose are attached
and secure.
2. Turn the pressure control knob fully counterclockwise to its
lowest pressure setting.
3. Make sure the pump ON/OFF switch is in the OFF position.
4. Fill the fluid section oil cup with approximately one
tablespoon of piston seal lubricant (Piston Lube).
ImPORTANT: Never operate unit for more than ten seconds
without fluid. Operating this unit without fluid will cause
unnecessary wear to the packings.
5. Check the engine oil level. The gasoline engine oil level
is determined by the manufacturer. Refer to the engine
manufacturer's service manual (supplied).
6. Close the fuel shut-off lever and fill the gas tank with gasoline.
Use only high quality, unleaded gasoline.
One-Gun Setup
1. Using a wrench, thread the 50' airless spray hose to the outlet
fitting on the sprayer. Tighten securely.
2. Attach an airless spray gun to the spray hose. Using two
wrenches (one on the gun and one on the hose), tighten
securely.
Two-Gun Setup
1. Using a wrench, thread the valve assembly (with 50' hose
attached) to the outlet fitting on the sprayer. Tighten
securely.
2. Using a wrench, thread the 6' airless spray hose to the top
outlet fitting on the valve assembly. Tighten securely.
6' hose
Valve
assembly
50' hose
Outlet
3. Attach an airless spray gun to each of the spray hoses. Using
two wrenches (one on the gun and one on the hose), tighten
securely.
NOTE: If you plan on using both guns, make sure the valve
handle is in the open position (handle is in line with
the 6' hose)
Valve
closed
© Titan Tool Inc. All rights reserved.
tting
Valve
open
Positioning the spray guns (both units)
1. Loosen the support bar knob and slide the gun support bar
to the desired horizontal position. Make sure the gun is far
enough away from the cart so that the rear wheel does not
track over the fresh spray pattern.
2. 2nd Gun mounting (if equipped) -
a. Slide the 2nd gun support bar assembly over the end of the 1st gun
support bar. Secure in place by tightening the 2nd gun support
bar knob.
b. Loosen the 2nd gun post knob and slide the post to the desired
horizontal position.
c. Run the 2nd gun cable through the block and cable guides,
underneath the frame and back towards the cart handle. Use the
tie wraps to secure the cable to the frame.
ImPORTANT: make sure the cable is not touching the tires or
interfering with the mobility of the cart in any way.
d. Insert the gun cable assembly into the hole of the control guide
until it snaps into place.
e. Attach the hooked end of the cable into the hole of the lever plate.
Control guide
NOTE: See the "Adjusting the Trigger Tension" section in
order to verify that the cable is installed properly.
3. Loosen the gun riser clamp(s) and slide the spray gun(s) to the
desired vertical position(s). A distance of 6" from the tip to the
spray surface is a good starting point.
Gun riser
clamps
Knob
2nd gun
support bar
Block
2nd gun
post knob
NOTE: The gun support bar and the spray gun(s) can be
mounted on either side of the sprayer. Refer to the
"Spray Gun Positions" illustration near the back of
this manual.
NOTE: The height of the spray gun affects the width of the
spray pattern (i.e., the lower the gun, the smaller
the line width). Tip size also affects line width.
5
Gun cable
Lever plate
Gun
support
bar
English
Support
bar knob