Tabla De Contenido; General Description; Operation; Setup - Titan 640i Manual Del Propietário

Table of Contents
Safety Precautions .................................................................2
General Description ...............................................................4
Operation ................................................................................4
Setup ....................................................................................4
Preparing to Paint .................................................................5
Painting .................................................................................5
Electronic Pressure Control Indicators .................................5
Pressure Relief Procedure ...................................................6
Spraying ..................................................................................6
Spraying Technique ..............................................................6
Practice .................................................................................7
Cleanup ...................................................................................7
Maintenance............................................................................8
General Repair and Service Notes.......................................8
Replacing the Motor .............................................................8
Replacing the Motor Brushes ...............................................8
Replacing the Gears .............................................................8
Replacing the Transducer.....................................................9
Replacing the PRIME/SPRAY Valve.....................................9
Servicing the Fluid Section .................................................10
Replacing the Filters ...........................................................11
Troubleshooting ...................................................................12
Warranty ................................................................................13
Parts Listings........................................................................38
Main Assembly....................................................................38
Motor Assembly ..................................................................39
Gear Box Assembly ............................................................40
Fluid Section Assembly ......................................................42
Suction Set Assembly .........................................................44
Stand Assembly ..................................................................44
Low Rider Assembly ...........................................................45
High Rider Assembly ..........................................................46
Siphon Tube Assembly (High Rider Assembly) ..................46
Accessories ........................................................................47
Electrical Schematic ...........................................................49

General Description

This airless sprayer is a precision power tool used for spraying
many types of materials. Read and follow this instruction
manual carefully for proper operating instructions,
maintenance, and safety information.
Return
Tube
Siphon
Hose
Motor
Circuit
Breaker
Filter

Operation

This equipment produces a fluid stream at
extremely high pressure. Read and understand
the warnings in the Safety Precautions section at
the front of this manual before operating this
equipment.
English

Setup

Perform the following procedure before plugging in the power
cord of an electric unit.
1. Ensure that the suction set/siphon tube and the return
hose are attached and secure.
2. Using a wrench, attach a minimum of 50' of 1/4" nylon
airless spray hose to the unit. Tighten securely.
3. Attach an airless spray gun to the spray hose. Using two
wrenches (one on the gun and one on the hose), tighten
securely.
NOTE: Do not attach the tip to the spray gun yet.
Remove the tip if it is already attached.
Make sure all airless hoses and spray guns are
electrically grounded and rated for at least 3200
psi (21.1 MPa) fluid pressure.
4. Make sure the pressure control knob is in its OFF position
in the black zone.
5. Make sure the ON/OFF switch is in its OFF position.
6. Fill the oil cup with one tablespoon of piston seal lubricant
(Piston Lube).
IMPORTANT: Never operate unit for more than ten
seconds without fluid. Operating this unit without fluid
will cause unnecessary wear to the packings.
7. Make sure the electrical service is 120V, 15 amp minimum.
8. Plug the power cord into a properly grounded outlet at
least 25' from the spray area.
IMPORTANT: Always use a minimum 12 gauge, three-wire
extension cord with a grounded plug. Never remove the
third prong or use an adapter.
Preparing a New Sprayer
If this unit is new, it is shipped with test fluid in the fluid section
to prevent corrosion during shipment and storage. This fluid
must be thoroughly cleaned out of the system with mineral
spirits before you begin spraying.
IMPORTANT: Always keep the trigger lock on the spray
gun in the locked position while preparing the system.
Pressure
1. Place the suction tube into a container of mineral spirits
Control
that has a flash point of 140ºF (60ºC) or above.
Knob
2. Place the return hose into a metal waste container.
ON/OFF
3. Set the pressure to minimum by turning the pressure
Switch
control knob to the "Min" setting in the yellow zone.
Oil Cup
Min. - 1800 PSI
PRIME/
(yellow zone)
SPRAY
Valve OFF
(black zone)
Fluid
Turbo PulseClean
Section
(red zone)
Outlet
OFF
Fitting
(black zone)
4. Move the PRIME/SPRAY valve down to the PRIME
position.
5. Turn the unit on by moving the ON/OFF switch to the ON
position.
6. Allow the sprayer to run for 15-30 seconds to flush the
test fluid out through the return hose and into the waste
container.
7. Turn the unit off by moving the ON/OFF switch to the OFF
position.
4
Min.
PSI
1800 - 3200 PSI
(green zone)
Max.
PSI
Pressure Control Knob
© Titan Tool Inc. All rights reserved.