Maintenance And Inspection - HIKOKI NP 18DSAL Instrucciones De Manejo

English
HOW TO USE THE CORDLESS PIN
NAILER
1. Driving in Pin Nails
WARNING
○ Never point the discharge outlet at people.
○ Make sure that work is carried out with the discharge
outlet well away from faces, hands, feet and other parts
of the body.
○ Do not fi re nails directly onto existing nails.
○ Disconnect the battery when the power tool is not
being used and during work breaks.
○ When work has been completed, disconnect the
battery, and then remove the remaining nails.
○ When pulling the trigger, make sure that other fi ngers
are not touching the push lever.
Failure to observe this may result in injury.
NOTE
○ Operation may become sluggish if used at low ambient
temperatures.
Move to a warm location and allow the power tool and
battery to warm up before using.
○ Do not use the power tool to nail fl ooring or fl oor
materials.
Accidentally standing on any nails that stick up may
lead to injury.
○ Nails may bend or cracks may appear in the material
depending on the hardness, thickness or combination
of materials. Fire a test nail before commencing full
use.
(1) Disconnecting the battery
Disconnect the battery from the power tool to prevent
unexpected operation. (Fig. 3)
(2) Loading the nails
Load pin nails of the appropriate size for the job into the
magazine.
(3) Attaching the nose cap
Attach the nose cap as necessary. (Fig. 10)
(4) Connecting the battery
Push the battery into the power tool until it clicks into
place.
(5) Driving in nails
○ Make sure the discharge outlet is fi rmly placed against
the place where the nail is to be discharged and pull the
trigger. (Fig. 17)
○ If the nails are not driven in completely, press the head
of the power tool down fi rmly when nailing.
○ To adjust the nailing depth, see the section "How to
Adjust the Nailing Depth."
<Safety Device>
Nails will not be discharged until the push lever is
pressed against the object to be nailed and the trigger
is pulled.
In other words, nails will not be discharged when
only the trigger is pulled, or when only the push lever
is pressed against the object to be nailed. This is to
prevent the nails from being discharged when the
trigger is accidentally pulled or when the push lever is
accidentally placed against something.
(6) Finishing work
When work is fi nished, disconnect the battery and then
remove all the nails.
2. How to Adjust the Nailing Depth
WARNING
Make sure that the trigger is turned off and the battery
has been disconnected before adjusting the adjuster.
The nailing depth can be adjusted by rotating the
adjuster. (Fig. 18)
Fire a test nail and if it is driven in too deep, adjust the
depth by rotating the adjuster toward the shallower
( mark).
If the nail is not driven in deep enough, rotate the adjuster
toward the deeper (
The adjuster modifi es the depth by 0.75 mm each time
it is rotated.
3. How to Handle the Nails
NOTE
○ Handle the nails with care.
If you drop them, the strip may break, and continued
use may result in blank fi ring or jamming due to
defective feeding. Do not use broken nail strips.
○ Do not leave the nails exposed to the outside air or
direct sunlight for long periods of time.
This may cause rust or defective strips. Store the nails
in the packing box, etc.
4. Storing the hexagonal bar wrench
The hexagonal bar wrench can be stored in the
magazine (Fig. 20).

MAINTENANCE AND INSPECTION

WARNING
Make sure the trigger is turned off and the battery has
been disconnected before carrying out inspections
and maintenance. Also make sure that the recharger
has been unplugged.
1. Removing Nail Jams (Fig. 21)
(1) Disconnect the battery and then remove all the nails in
the magazine.
(2) Detach the nose and guide plate using the hexagonal
bar wrench stored in the back of the magazine.
NOTE
Do not remove the two bolts shown in the fi gure.
(3) Remove any nails, adhesive, fragments, splinters or
other foreign objects jammed in the guide groove of the
push lever or the blade guide. (Table 2)
Driver blade
position
(1) Bend the driver blade back with
(2) Remove the nails with the pliers.
Blade guide side
(Fig. 22)
(3) Remove any nail fragments or dirt
(1) Remove the nails with the pliers.
Push lever side
(2) Remove any nail fragments or dirt
(Fig. 25)
(4) Attach the guide plate and nose.
Tightening it with the hexagon hole bolt M4×6.
(5) After assembling, pull out the push lever and nose and
check that they move up and down smoothly. (Fig. 27)
If any jammed nails remain, movement will not be
smooth.
In this case, repeat from step (1) again.
24
mark). (Fig. 18 and 19)
Table 2
How to remove jammed nails
the slotted screwdriver. (Fig. 23)
(Fig. 23)
that remains in the guide groove
with the slotted screwdriver.
(Fig. 24)
(Fig. 26)
that remains in the guide groove
with the slotted screwdriver.