Skil 2036 Instrucciones página 5

GB
INTRODUCTION
This tool with left/right rotation is intended for
screwdriving in wood
TECHNICAL SPECIFICATIONS 1
SAFETY
Read and save this instruction manual (pay special
attention to the safety instructions at the back) 2
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the charger
(chargers with a rating of 230V or 240V can also be
connected to a 220V supply)
In case of electrical or mechanical malfunction,
immediately switch off the tool or unplug charger from
power source
SKIL can assure flawless functioning of the tool only
when original accessories are used
This tool should not be used by people under the age of
16 years
Be careful not to drive into areas where electrical wires
may be contacted
Do not activate switch when changing accessories or
carrying the tool
CHARGING/BATTERIES
Charge battery only with the charger that is supplied
with the tool
Do not expose tool and charger to rain
Never charge battery outdoors 3
Store tool and charger in locations where temperature
will not exceed 40°C or drop below 0°C
Batteries will explode in fire, so do not burn battery for
any reason
When damaged, and under extreme usage and
temperature conditions, batteries may start to leak
- if liquid comes into contact with the skin, wash quickly
with soap and water, then with lemon juice or vinegar
- if liquid gets into the eyes, flush eyes with clean water
for a minimum of 10 minutes and seek immediately
medical attention
Do not use tool or charger when damaged; take it to one
of the officially registered SKIL Service Stations for a
safety check
Do not disassemble charger or battery
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of the charger to the earth terminal of the
plug
If for any reason the old plug is cut off the cord of the
charger, it must be disposed of safely and not left
unattended
USE
Charging battery 4
- battery of new tools is not fully charged
! unplug the charger from the tool after charging
period has ended thereby lengthening the service
life of the battery
IMPORTANT:
- while charging, the charger and the tool may become
warm to touch; this is normal and does not indicate a
problem
- do not charge at temperatures below 0°C and over
40°C; this will seriously damage the battery as well as
the charger
- when you charge the battery for the first time, it only
accepts 80% of its maximum capacity; after several
charges and discharges, however, the batteries should
be at full capacity and deliver maximum performance
- do not repeatedly recharge the battery after only a
few minutes of operation; this may result in a
reduction of operating time and battery efficiency
- the nickel-cadmium battery must be kept separate from
the natural environment and should not be disposed of
as normal domestic waste 5 (symbol 5a will remind
you of this when the need for disposing occurs)
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
- if you anticipate long periods of non-use for the tool,
it is best to unplug the charger from its power source
On/Off & Changing direction of rotation 6
Changing bits 7
- push bit to end position in bit holder
! never use bits shorter than 30 mm
! do not use bits with a damaged shank
Automatic spindle-lock
Allows you to manually tighten or loosen screws, when
necessary 8
APPLICATION ADVICE
Use the appropriate bits 9
! do not use damaged bits
When turning in a screw at/near the cross cut end or an
edge of wood one should pre-drill a hole in order to
avoid cracking of the wood
For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
When screwdriving in hard wood one should pre-drill a
hole
For more tips see www.skileurope.com
GUARANTEE / ENVIRONMENT
Keep tool and charger clean
- clean charging contacts of charger with alcohol or
contact cleaner
! unplug charger from power source before cleaning
This SKIL product is guaranteed in accordance with
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling will
be excluded from the guarantee
5