Power Stroke PS80931 Serie Manual Del Operador página 14

NOTICE:
This product is not equipped with a spark arrestor
and cannot be used on U.S. forest lands; in addition,
product users must comply with Federal, State, and
local fire prevention regulations. Check with appropriate
authorities. Refer to accompanying engine manual for
maintenance and replacement parts.
NOTICE:
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please call 1-877-617-3501 or contact an
authorized service center for assistance.
APPLICATIONS
You may use this tool around the house for cleaning most
small to large horizontal or vertical exterior surfaces, smaller
exterior objects and structures, and outdoor equipment and
tools.* You can:
 Clean or remove mold and mildew from weathered decks,
driveways, patios, walkways, sidewalks, etc.
 Remove dirt from various exterior vertical surfaces such
as house exteriors, siding, fences, brick, concrete or stone
walls, etc.
 Wash boats, outdoor furniture, powered or non-powered
garden equipment, gutters, window screens, grills,
playground equipment, etc.
*Always test in an inconspicuous area first.
ADDING/CHECKING ENGINE LUBRICANT
See Figure 7.
NOTE: This machine has been shipped with approximately
2 oz. of lubricant in the engine from testing. You must add
lubricant to the engine before starting it the first time.
NOTICE:
Any attempt to start the engine without adding lubricant
will result in engine failure.
To add engine lubricant:
 Place pressure washer on a flat, level surface. Do not tilt.
 Unscrew the oil cap/dipstick by turning counter-
clockwise.
 Before first use, squeeze the entire contents of the
lubricant container provided into the oil reservoir.
After initial use, add 4-stroke engine lubricant (SAE 30 or
SAE 10W30) until the fluid level rises to the upper portion
of the hatched area on the dipstick. Do not overfill.
 Replace the oil cap/dipstick and securely tighten.
All manuals and user guides at all-guides.com
OPERATION
To check engine lubricant level:
 Place pressure washer on a flat, level surface. Do not tilt.
 Unscrew the oil cap/dipstick by turning counter-
 Wipe dipstick clean and re-seat in hole; do not rethread.
 Remove dipstick again and check lubricant level.
 If level is low, add engine lubricant until the fluid level rises
 Replace and secure the oil cap/dipstick.
OXYGENATED FUELS
Fuel system damage or performance problems resulting
from the use of an oxygenated fuel containing more than
the percentage of oxygenates stated below are not covered
under warranty.
Ethanol. Gasoline containing up to 10% ethanol by volume
(commonly referred to as E10) is acceptable. E15 and E85
are not.
ADDING GASOLINE TO THE FUEL TANK
See Figure 8.
When adding gas to the pressure washer, make sure the unit
is sitting on a flat, level surface. If the engine is hot, let the
pressure washer cool before adding gas. ALWAYS fill the
fuel tank outdoors with the machine turned off.
NOTE: This is a 4-cycle engine. Do not mix fuel and
lubricant together.
 Mix fuel stabilizer with gasoline according to fuel stabilizer
 Before removing the fuel cap, clean the area around it.
 Insert a clean funnel into the fuel tank then slowly pour
Page 10 — English
clockwise.
Lubricant level should fall within the hatched area on the
dipstick.
to the upper portion of the hatched area on the dipstick.
NOTICE:
Do not overfill. Overfilling the crankcase may cause
excessive smoke and engine damage.
NOTICE:
Do not use E15 or E85 fuel (or fuel containing greater
than 10% ethanol) in this product. It is a violation of
federal law and will damage the unit and void your
warranty.
WARNING:
Gasoline and its vapors are highly flammable and
explosive. To prevent serious personal injury and property
damage, handle gasoline with care. Keep away from
ignition sources, handle outdoors only, do not smoke
while adding fuel, and wipe up spills immediately.
manufacturer's directions.
Remove the fuel cap.
gasoline into the tank. Fill tank to approximately 1-1/2 in.