Interrupting Operation; Ending Operation; How To Use The Accessories; Care And Service - Kärcher WD 5 Manual Del Usuario

Working with power tools (only for devices
with a built-in socket)
CAUTION
Unintentional starting of the power tool
Injury or property damage
Make sure that the power tool is ready for operation as
soon as it is connected to the device socket.
1. Connect the suction hose.
Illustration H
2. If necessary, the adapter can be adjusted to the con-
nection diameter of the power tool with a suitable
tool.
3. Option A) Put the adapter on the handle of the suc-
tion hose. Connect the suction hose to the adapter
on the power tool.
Option B) For more flexibility when working, connect
the adapter to the thin tool hose and the handle of
the suction hose and connect it to the power tool.
Option C) With some power tools, the handle of the
suction hose can be connected directly to the power
tool.
Illustration N
4. Plug the mains plug of the power tool into the device
socket.
Illustration O
5. Set the trigger to MAX
The power can be regulated using the rotary switch.
The suction is activated automatically.
Illustration M
Note
Note the maximum connected load (see information on
the device socket).
Note
As soon as the power tool is switched on, the suction
turbine starts up with a 0.5 second delay. If the power
tool is switched off, the suction turbine continues to run
for approx. 5 seconds in order to suck in the residual dirt
in the suction hose.
Integrated filter cleaning system
Note
The filter cleaning system is designed for vacuuming
large quantities of fine dust without a filter bag inserted.
The filter cleaning system allows the soiled flat pleated
filter to be cleaned at the push of a button and the suc-
tion performance to be increased again.
 Place the handle of the suction hose in the designat-
ed parking position on the device head. Press the fil-
ter cleaning button three times with the device
switched on, waiting 4 seconds between the individ-
ual actuations.
Illustration P
Note
After pressing the filter cleaning button several times,
check the container for its filling volume. Otherwise dirt
can escape when the container is opened
Blower function
The blower function can be used to clean areas that are
difficult to reach or where vacuuming is not possible,
e.g. leaves in a gravel bed.
 Insert the suction hose into the blower connection.
The blower function is now activated.
Illustration Q

Interrupting operation

1. Set the trigger to "0 OFF".
The device is switched off.
10
Set.
English
2. Variant 1: Place the handle of the suction hose in the
intermediate parking position.
Variant 2: Attach the floor nozzle in the parking po-
sition.
Illustration R

Ending operation

1. Set the trigger to "0 OFF".
The device is switched off.
2. Pull out the mains plug.
3. Remove the device head.
Illustration B
4. Empty the container.
On the devices that have a drain screw, the contain-
er can be emptied via the drain screw.
Illustration S
5. Storage possibility:
Illustration Y
Note
The suction hose can be wrapped around the device
head and attached to the device head with the help of
the hose collar.
6. Store the device in a dry and frost-proof room.

How to use the Accessories

General instructions for use
 Connect the coarse dirt hose with the coarse dirt
pipes.
 Connect the coarse dirt pipes with the coarse dirt
floor nozzle.
Illustration J
 Connect the accessories, such as the suction brush,
to the handle or attach it directly to the suction hose.
Coarse dirt accessories
ATTENTION
Vacuuming coarse dirt with a filter bag
Damage to the filter bag
Only vacuum coarse dirt only the filter bag inserted.
● Use the coarse dirt hose, the coarse dirt pipes and
the coarse dirt floor nozzle to vacuum coarse dirt
and small stones.
Suction brush with soft bristles
● For gently cleaning sensitive surfaces or delicate
items such as those on the workbench.

Care and service

General care instructions
 Clean the device and plastic accessory parts with a
commonly available plastic cleaner.
 Rinse the container and accessories with water, as
necessary, and dry them before further use.
Clean the filter box / flat pleated filter
1. Unlock the filter box and fold it out.
Illustration T
2. Remove the filter box.
Illustration U
3. Empty the filter box into a waste container. In the
case of heavy soiling, tap the filter box against the
edge of the waste container. The flat pleated filter
does not have to be removed from the filter box.
Illustration V
If necessary, clean the flat pleated filter separately.