Bosch GCM 12 GDL Professional Manual Original página 33

32 | English
debris or loose pieces of wood or other objects that con-
tact the revolving blade can be thrown with high speed.
Cut only one workpiece at a time. Stacked multiple
u
workpieces cannot be adequately clamped or braced and
may bind on the blade or shift during cutting.
Ensure the mitre saw is mounted or placed on a level,
u
firm work surface before use. A level and firm work sur-
face reduces the risk of the mitre saw becoming unstable.
Plan your work. Every time you change the bevel or
u
mitre angle setting, make sure the adjustable fence is
set correctly to support the workpiece and will not in-
terfere with the blade or the guarding system. Without
turning the tool "ON" and with no workpiece on the table,
move the saw blade through a complete simulated cut to
assure there will be no interference or danger of cutting
the fence.
Provide adequate support such as table extensions,
u
saw horses, etc. for a workpiece that is wider or
longer than the table top. Workpieces longer or wider
than the mitre saw table can tip if not securely supported.
If the cut-off piece or workpiece tips, it can lift the lower
guard or be thrown by the spinning blade.
Do not use another person as a substitute for a table
u
extension or as additional support. Unstable support
for the workpiece can cause the blade to bind or the
workpiece to shift during the cutting operation pulling you
and the helper into the spinning blade.
The cut-off piece must not be jammed or pressed by
u
any means against the spinning saw blade. If confined,
i.e. using length stops, the cut-off piece could get wedged
against the blade and thrown violently.
Always use a clamp or a fixture designed to properly
u
support round material such as rods or tubing. Rods
have a tendency to roll while being cut, causing the blade
to "bite" and pull the work with your hand into the blade.
Let the blade reach full speed before contacting the
u
workpiece. This will reduce the risk of the workpiece be-
ing thrown.
If the workpiece or blade becomes jammed, turn the
u
mitre saw off. Wait for all moving parts to stop and
disconnect the plug from the power source and/or re-
move the battery pack. Then work to free the jammed
material. Continued sawing with a jammed workpiece
could cause loss of control or damage to the mitre saw.
After finishing the cut, release the switch, hold the
u
saw head down and wait for the blade to stop before
removing the cut-off piece. Reaching with your hand
near the coasting blade is dangerous.
Hold the handle firmly when making an incomplete cut
u
or when releasing the switch before the saw head is
Symbols
The following symbols may be important for the operation of your power tool. Please take note of these symbols and their
meaning. Correctly interpreting the symbols will help you to operate the power tool more effectively and safely.
1 609 92A 5RR | (02.07.2020)
completely in the down position. The braking action of
the saw may cause the saw head to be suddenly pulled
downward, causing a risk of injury.
Keep your work area clean. Material mixtures are partic-
u
ularly hazardous. Light metal dust may catch fire or ex-
plode.
Do not use dull, cracked, bent or damaged saw blades.
u
Unsharpened or improperly set saw blades produce
narrow kerf causing excessive friction, blade binding
and kickback.
Do not use saw blades made from high speed steel
u
(HSS). Such saw blades can easily break.
Always use saw blades with correct size and shape
u
(diamond versus round) of arbour holes. Saw blades
that do not match the mounting hardware of the saw will
run off-centre, causing loss of control.
Never remove cuttings, wood chips, etc. from the cut-
u
ting area while the power tool is running. Always guide
the tool arm back to the neutral position first and then
switch the power tool off.
Do not touch the saw blade after working before it has
u
cooled. The saw blade becomes very hot while working.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Warning! If operating or adjustment devices other
u
than those specified here are used or other proced-
ures are carried out, this can lead to dangerous expos-
ure to radiation.
Do not replace the integrated laser with a laser of an-
u
other type. A laser that is not compatible with this power
tool could pose a risk to persons.
Do not make any modifications to the laser equip-
u
ment. The setting options described in these operating
instructions can be used safely.
Do not direct the laser beam at persons or
animals and do not stare into the direct or
reflected laser beam yourself. You could
blind somebody, cause accidents or damage
your eyes.
Never make warning signs on the machine unrecognis-
u
able.
Autogoods "130"
Bosch Power Tools