Specific Safety Instructions; Ilustrated Description - stayer RO125 Manual De Instrucciones

The machine is intended for dry sanding of wood, plastic,
metal, filler as well as coated surfaces.
Machines with electronic control are also suitable for
polishing.
This manual is consistent with the date of manufacture of
your machine, you will find information on the technical
data of the machine acquired manual check for updates of
our machines on the website: www.grupostayer.com

Specific safety instructions

- Use the machine only for dry sanding. Penetration of
water into the machine increases the risk of an electric
shock or damaged.
- Pay attention that no persons are put at risk through
sparking. Remove any combustible materials in
the vicinity. Sparking occurs when sanding metal
materials.
- Caution, fire hazard! Avoid overheating the object
being sanded as well as the sander. Always
empty the dust collector before taking breaks. In
unfavourable conditions, e. g., when sparks emit from
sanding metals, sanding debris in the dust bag, micro
filter or paper sack (or in the filter sack or filter of the
vacuum cleaner) can selfignite. Particularly when
mixed with remainders of varnish, polyurethane or
other chemical materials and when the sanding debris
is hot after long periods of working.
- When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
- Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
Instructions for use
Placement tool
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
While reading the operating instructions, unfold the
graphics page for the machine and leave it open.
Use this power tool for dry sanding or polishing
Assembly (figure1).
Before any work on the machine itself, pull the mains
plug.
The machine is completely assembled, except
sanding sheet 8.
To position the sanding sheet 8 should attach to velcro support
plate 5, taking into account that the suction holes coincide.
ENGLISH
17
Auxiliary handle
The auxiliary handle 10 allows comfortable handling
and even distribution of force, especially if the material
removal rate is high.
Screw the auxiliary handle 10 to the right or left on the
spindle thread 1.

Ilustrated description

The numbering of the product features refers to the
illustration of the machine on the graphics page.
1 Rubber Head.
2 Suction nozzle.
3 Wick holder.
4 Catch.
5 Back plate.
6 Sanding plate screws.
7 Key.
8 Sanding sheet *.
9 Grip (nip isolated).
10 Auxiliary handle.
11 Switch on / off.
12 Suction tube.
13 Screw fastening the suction tube.
14 Thumbwheel for preselection of number
of oscillations.
15 Fixing button
16 Power on machine
* Accessories shown or described are not part of the standard
delivery scope of the product. A complete overview of accessories
can be found in our accessories program.
Operating instructions
Placement and testing
Network connection
Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified on
the nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
To start the machine, push the On/Off switch 11 forwards.
To lock the On/Off switch 11, press the On/Off switch 11
down at the front until it latches.
To switch off the power tool, release the On/Off switch 11
or, if it is locked, briefly push down the back of the On/Off
switch 11 and then release it.
Preselecting the Orbital Stroke Rate
With the thumbwheel for preselection of the orbital stroke
rate 14, you can preselect the required orbital stroke rate,
even during operation.
1 – 2 Low stroke rate
3 – 4
Medium stroke rate
5 – 6 High stroke rate
The required stroke rate depends on the material and
the working conditions and can be determined through
practical testing.
17