Electrical Safety; Assembly Instructions; Description Illustration A; Description Illustration B - Tunturi S40 Sprinter Bike Front Manual Del Usuario

English
- Make sure that only one person uses the equipment at a time� The
equipment must not be used by persons weighing more than 150
kg (330 lbs) �
- Do not open equipment without consulting your dealer�

Electrical safety

(Only for equipment with electric power)
- Before use, always check that the mains voltage is the same as the
voltage on the rating plate of the equipment�
- Do not use an extension cable�
- Keep the mains cable away from heat, oil and sharp edges�
- Do not alter or modify the mains cable or the mains plug�
- Do not use the equipment if the mains cable or the mains plug
is damaged or defective� If the mains cable or the mains plug is
damaged or defective, contact your dealer�
- Always fully unwind the mains cable�
- Do not run the mains cable underneath the equipment� Do not run
the mains cable underneath a carpet� Do not place any objects on
the mains cable�
- Make sure that the mains cable does not hang over the edge of a
table�
- Make sure that the mains cable cannot be caught accidentally or
tripped over�
- Do not leave the equipment unattended when the mains plug is
inserted into the wall socket�
- Do not pull the mains cable to remove the mains plug from the wall
socket�
- Remove the mains plug from the wall socket when the equipment
is not in use, before assembly or disassembly and before cleaning
and maintenance�
⚠ WARNING
• Never use water or any other liquid directly on or near the
equipment, but only via a damp cloth if moist is required to
clean the machine�
• Using liquid directly is harmful for the equipment's components,
and may result in an electric shock caused by a short cut circuit�
This could result in serious personal injury or even death�

Assembly instructions

Description illustration A

The illustration shows what the trainer will looks like after the
assembly is completed�
You can use this as a reference during your assembly, but do follow
the assembly steps always in the correct sequence as showed in the
illustrations�

Description illustration B

The illustration shows what components and parts you should find
when un-boxing your product�
‼ NOTE
• Small parts can be hidden/ packed in hollow spaces in the
Styrofoam product protection
• If a part is missing, contact your dealer�

Description illustration C

The illustration shows the hardware kit that comes with your product�
The hardware kit contains bolts, washers, screws , nuts etc� and the
required tools to properly fit your trainer�

Description illustration D

The illustrations shows you in the correct following order how to
assembly your trainer best�
‼ NOTE
• Part numbers shown in the assembly steps are commencing with
the spare part drawing that can be found in the online version
user manual�
⚠ WARNING
• Assemble the equipment in the given order�
• Carry and move the equipment with at least two persons�
⚠ CAUTION
• Place the equipment on a firm, level surface�
• Place the equipment on a protective base to prevent damage to
the floor surface�
• Allow at least 100 cm of clearance around the equipment�
• Refer to the illustrations for the correct assembly of the
equipment�

Additional assembly information

D2 How to fit the pedals correctly�
‼ NOTE
• Right and left side are determined from an exercising positions
perspective�
Right hand pedal
Find the "R" or "L" mark on the pedal axle
- Fit the right hand pedal "R" into the right hand crank�
- Firstly turn the pedal axle in clockwise direction by hand�
- Use the wrench to fully tighten the pedal�
Left hand pedal
- Fit the left hand pedal "L" into the left hand crank�
- Firstly turn the pedal axle in counter-clockwise direction by hand�
- Use the wrench to fully tighten the pedal�
Click to see our supportive YouTube video
https://youtu�be/Devel2ZhCAc
‼ NOTE
• Save the tools provided with this product, after you completed
the product assembly,
for future service purposes�

Additional information

Packaging disposal
Government guidelines ask that we reduce the amount of waste
material disposed of in land fill sites� We therefore ask that you
dispose of all packaging waste responsibly at public recycling centres�
1 4