Machine-Specific Safety Warnings; Product Features; Functional Description - stayer 384B Manual De Instrucciones

Machine-specific Safety Warnings

- Hold the machine with a firm grip. High reaction torque can briefly
occur while driving in and loosening screws.
- Secure the workpiece. A workpiece clamped with clamping devices or
in a vice is held more secure than by hand.
- Always wait until the machine has come to a complete stop before
placing it down. The tool insert can jam and lead to loss of control over
the power tool.
- Never use the machine with a damaged cable. Do not touch the
damaged cable and pull the mains plug when the cable is damaged
while working. Damaged cables increase the risk of an electric shock.
BATTERIES USE AND CARE
Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against continuous intense
sunlight, fire, water, and moisture. Danger of explosion.
In case of damage and improper use of the battery, vapours may be
emitted. Provide for fresh air and seek medical help in case of complaints.
The vapours can irritate the respiratory system.
Use the battery only in conjunction with your STAYER power tool. This
measure alone protects the battery against dangerous overload.
Use only original STAYER batteries with the voltage listed on the
nameplate of your power tool. When using other batteries, e. g. imitations,
reconditioned batteries or other brands, there is danger of injury as well
as property damage through exploding batteries.
Do not continue to press the On/Off switch after the machine has been
automatically switched off. The battery can be damaged.
The battery is equipped with a temperature control which allows charging
only within a temperature range of between 0 °C and 45 °C. A long
battery service life is achieved in this manner.
Observe the notes for disposal.
Use only the battery chargers listed on the accessories page. Only these
battery chargers are matched to the lithium ion battery of your power
tool.
The battery is supplied partially charged. To ensure full capacity of the
battery, completely charge the battery in the battery charger before using
your power tool for the first time.
The lithium-ion battery can be charged at any time without reducing its
service life. Interrupting the charging procedure does not damage the
battery.
The lithium-ion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit: The inserted
tool no longer rotates.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be subject to overload.
When the load is too high or the allowable battery temperature range of
0–50 °C is exceeded, the speed is reduced. The power tool will not run
at full speed until reaching the allowable battery temperature. position.
Unintentional actuation of the On/Off switch can lead to injuries.
Open the keyless chuck 2 by turning in rotation direction , until the tool
can be inserted. Insert the tool. Firmly tighten the collar of the keyless
chuck 2 by hand in rotation direction . This automatically locks the drill
chuck.
The locking is released again to remove the tool when the collar is turned
in the opposite direction.

Functional Description

Read all safety warnings and all instructions. Failure to follow the
warnings and instructionsmay result in electric shock, fire and/or serious
injury.
While reading the operating instructions, unfold the graphics page for the
machine and leave it open.
Intended Use
The machine is intended for driving in and loosening screws.
ENGLISH
13

Product Features

The numbering of the product features refers to the illustration of the
machine on the graphics page.
1- Replaceable screwdriver tip
2- Limit cap
3- Adjusting sleeve for depth stop
4- Screw depth stop
5- Direction of rotation selector
6- Switch interlock button
7- On / off switch
8- Belt attachment clip
9- Universal screwdriver bit holder
10- Battery (DWS L20 - depending on model)
11- Battery removal button (DWS L20)
12- LED for the lighting of the screwing place (DWS L20)
13- Charger (DWS L20 - depending on model)
14- Bit holder (DWS L20)
Noise/Vibration Information
Measured values determined according to EN 62841-1
Wear hearing protection!
The vibration emission level given in this information sheet has been
measured in accordance with a standardised test given in EN 62841-1
and may be used to compare one tool with another. It may be used for a
preliminary assessment of exposure.
The declared vibration emission level represents the main applications
of the tool. However if the tool is used for different applications, with
different accessories or poorly maintained, the vibration emission may
differ.
This may significantly increase the exposure level over the total working
period.
An estimation of the level of exposure to vibration should also take into
account the times when the tool is switched off or when it is running but
not actually doing the job. This may significantly reduce the exposure
level over the total
working period.
Identify additional safety measures to protect the operator from the
effects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
Technical Data on page 5
The values given are valid for nominal voltages [U] 230/240 V ~ 50/60 Hz
- 110/120 V ~ 60Hz. For lower voltage and models for specific countries,
these values can vary.
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
Operation
Starting Operation
- Observe correct mains voltage! The voltage of the power source
must agree with the voltage specified on the nameplate of the
machine. Power tools marked with 230 Vcan also be operated with
220 V.
Reversing the Rotational Direction
The rotational direction switch 8 is used to reverse the rotational direction
of the machine.
However, this is not possible with the On/Off switch 7 actuated.
Right rotation: For driving in screws, push the rotational direction switch
8 left to the stop.
Left rotation: Push the rotational direction switch 8 right to the stop (for
unscrewing screws).
Switching On and Off
To start the machine, press the On/Off switch 7 and keep it depressed.
13