Specific Safety Instructions - stayer BJ120B Manual De Instrucciones

This manual is consistent with the date of manufacture of
your machine information under the Data Table technicians
acquired the machine, check for updates Manuals our
machines on the website:
www.grupostayer.com
The machine is designed for milling slots to engalletado
unions in chipboard wood, hardwood and softwood,
plywood, fibreboard or artificial marble.

1. Specific safety instructions

- The disc cutters shall be suitable to withstand
revolutions least indicated in the tool supply. To
run at a speed excessive, the disc cutters can come to
disintegrate and cause accidents.
- Hold power tool by the handles isolated as strawberry
could even damage the network cable thereof. Contact
with drivers Low voltage can also put under tension metal
parts of the machine and cause electric shock.
- Always use milling cutters with dimensions correct
and proper hole. The milling cutters that do not fit properly
on the elements of coupling the device, and can rotate
eccentric to lose control over it.
- Only approximates the power tool against the
workpiece. in case otherwise you may suddenly back off
device snagged in the work piece.
- Keep hands away from cutting area and Strawberry.
Keep your second hand grip Additional. If the router
is held with both hands, they can not be cut by the cutter.
- Never rout over metal objects, nails or screws.
This could damage the cutter and cause vibrations
excessive.
- Use a suitable scanning devices for possible water
and gas pipes or cables Electrical hidden, or consult
the company Local supplies you with energy.
Contact with electric wires can shock you or cause a fire.
By damaging gas pipes, this may lead to an explosion. A
perforated pipe water can result in property damage or
cause electrocution.
- Do not use dull or damaged strawberries. The jagged
strawberries damaged or increase friction, they can be
caught, and cause an imbalance.
- Work on a firm foundation holding the tool electric
with both hands. tool Power is guided more safely with
both hands.
- Secure the workpiece. A workpiece clamped with
clamping devices, or in a screw bank, it remains subject
to more safely that hand.
- Before depositing, wait until it has stopped the
power tool. The tool can snag and to lose control over
the tool supply.
- Use the (s) handle (s) extra (s), if supplied with the
machine. loss control ºover the power tool may cause an
accident.
- Always be mounted anti-slip 7.
- Only use the tools listed in these instructions. Do not
mount cutting discs or saw blades.
- Only operate the spindle lock button 14 spindle
being stopped.
- Before starting make sure the milling cutter is secure
- The male connection plug must be connected
only to a socket of the same technical characteristics
of the plug in
2. Instructions for use
Posizionamento
Read all safety warnings and instructions.
Failure to comply to the warnings and
instructions following, this may cause a
ENGLISH
18
discharge electrical, fire and / or serious injury.
Deployment and keeps the flap open with the image the
device while reading the instructions.
-Working On a firm foundation holding the tool electric
with both hands. Tool Power is guided more secure with
both hands.
-Keep Hands away from cutting area and the cutter
disk. When working with one hand hold the handle 1 and
the other auxiliary handle 15.
- Only approximates the power tool performance
against the workpiece. In case otherwise you may
suddenly go back the device to snagged in the work piece.
Perform milling with a uniform feed
Mounting
Mounting and change the cutter disk
Before any work on the tool power, remove the
plug from the outlet.
When installing or replacing disc cutters is re-
commended use protective gloves.
Protect strawberries shocks and bumps.
The machine must be used exclusively with the cutter disk
provided by the manufacturer.
If not already be in that position, set the ceiling for angles
17-0 ° (see "Adjusting the angle milling) and vertical
adjustment cap 9 to the maximum height (see "Adjustment
the top of vertical adjustment).
Place the machine with the base plate 33 facing upwards
.
Loosen and remove the screw 32 and proceed to remove
the metal cover 31.
Operate the spindle lock button 14 and hold pressed, turn
the cutter until it locks.
Loosen the lock nut wrench 24 with two pivots 23 attached,
and remove the nut. Release the lock button 14.
If found bur mounted disk 25, remove it and clean it out
through the front slot. Also remove the mounti ng flange
28 and clean.
Enter the support flange 28 in the milling spindle 29 I
ensuring it is centered above the neck 27. The support
flange must be received between both sides milled (forced
drag).
Place the cutter 25 clean disk supporting flange 28, as
stated, so that it is visible arrow direction of rotation 26
on the cutter disk. The sense of arrow must match the
direction of the arrow 13 head edge machine. The hole
Strawberry disc should be housed in the centering collar
27 of the mounting flange.
Screw the lock nut 24 on the spindle for milling 29. Tighten
the lock nut with wrench two pivots 23 while holding down
the button spindle lock 14, to retain the spindle 29.
Check if it is properly installed, without touching
18