Circular Saw Blades - Fein RSG Ex 1500 A Manual De Instrucciones

Ocultar thumbs Ver también para RSG Ex 1500 A:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 50
en
20
Lubricants for sliding surfaces
For lubrication and servicing of sliding surfaces, we recommend using plain, acid-
free, watertight, brand plain bearing greases.
I
3
2 3
3
Troubleshooting (Design RSG Ex (**)).
Malfunction
Motor and application tool fail
Defective drive sprocket
Faulty cutting process
Reduced or ineffective machine function
Heavy vibrations
Warranty.
The warranty for the product is valid in accordance with the legal regulations in the
country where it is marketed.
Application Tools and Accessories.

Circular saw blades

1
3
Possible Cause
Very low ambient temperatures
Blunt or dull application tool
No mains voltage
Incorrect mains voltage
Feed rate too fast or too high material removal during
one run
Oil loss at gearbox
Excessive temperature increase in motor
Damaged chain piece
Chain incorrectly connected
Chain pin only partially inserted
Incorrect alignment of pipe milling machine and chain see section "Preliminary work on the pipe milling
Guide shaft not eccentric
Blunt or dull application tool
Inclined or vertically seated pipe or pipe out of round Use track guidance device, see section "Clamping the
Application tool overloaded
No mains voltage
Switch not switched on
Clutch slips
Feed rate too fast
Application tool immersed too deep
Clamping lever (11) not tightened
Chain loose
Blunt or dull application tool
2
3
Lubricating point
2 (gearbox)
3 (sliding surfaces and moving threads) Plain bearing grease
Corrective Action
Use FEIN gear oil for low temperatures
Replace application tool
Check mains supply and switchgear
Check mains supply data
Adapt gearing and/or reduce immersion depth
Locate leakage and correct cause – Refill oil
Reactivate switchgear assembly 3 07 02 041 01 4
Replace chain piece
Check connection points and correct
Fully insert chain pin
machine (see Fig. A)." on page 16 and section "Clamp-
ing the pipe milling machine on the pipe." on page 16
Readjust the running accuracy, see section "Adjusting
the running accuracy". on page 17
Replace application tool
pipe milling machine on the pipe." on page 16 and sec-
tion "Track guidance" on page 19
Adapt gearing and/or reduce immersion depth
Check mains supply and switchgear
Check switch
Adjust gearing or have the response torque of the
clutch adjusted at the FEIN factory.
Adjust gearing
Retract application tool setting
Tighten clamping lever
Check chain tension
Replace application tool
Form 1, HSS, for gear type:
A, B - For machining steel pipes
Ø
Width
Weight
(mm)
(mm)
(kg)
160
4
0.5
180
4
0.7
200
4
0.9
220
4
1.3
Form 2, HSS, for gear type:
B - For machining cast iron pipes
Ø
Width
Weight
(mm)
(mm)
(kg)
160
4
0.5
180
4
0.7
200
4
0.6
Lubricant or operating material
See Table: Lubricating oil for tool spin-
dle head
Number
Max. cut-
Order number
of teeth
ting depth
(mm)
50
25
6 35 02 022 00 6
60
35
6 35 02 037 00 8
64
45
6 35 02 053 00 7
70
55
6 35 02 041 00 1
Number
Max. cut-
Order number
of teeth
ting depth
(mm)
40
25
6 35 02 050 00 1
46
35
6 35 02 098 00 0
50
45
6 35 02 099 00 4

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Rsg ex 1500 bRsg ex 18 aRsg ex 18 b

Tabla de contenido