Arregui RESIST Manual De Instrucciones página 11

Ocultar thumbs Ver también para RESIST:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

Thank you for purchasing this RESIST safe. We advise you to
read the instructions before you install and use the safe to
prevent its improper use from making the guarantee void.
1. CHARACTERISTICS OF THE PRODUCT
This safe is meant to protect your objects of value and your
documents in the event of a possible fire. Due to its heavy
weight, it is advisable to place it on firm flooring.
FRONT DIAGRAM OF THE SAFE:
1
2. OPENING AND CLOSING THE SAFE
2.1.BATTERIES INSTALLATION AND OPENING
• Extract the battery compartment located outside the safe, at
the lower part of the keyboard, and place 4 alkaline batteries
of 1.5 V.
• Press the * key. A beep sounds and a green LED flashes.
• Enter opening code ( initial master-code is 1-2-3-4- 5-6)
• Every key pressing is confirmed with a beep sound and a
green led flashing. If the key is not pressed over the course
of 10 sec. the lock will switch off and the operation must be
repeated.
• Press ENTER
• While the green led is flashing, turn the key clockwise and
open the door.
• If the typed code is incorrect 2 beeps sounds and a red LED
flashes during 5 seconds. In this case, start the operation
again.
• The safe allows up to 3 erroneous code entries before it is
blocked for 5 minutes as a security measure. During this time,
it is not possible to use the keypad. During the blocking period
the red LED on the keyboard flashes in 5 seconds intervals.
WARNING:
For your own security, it is recommended to
change the opening code as soon as you
open the safe for the first time (see point 3).
2.2. CLOSING
To close the safe, push the door and insert the key and turn it
towards left
3. PROGRAMMING OPENING CODES
This safe has 2 opening codes from 1 to 8 digits each one: a
master code and a user code.
2
1. KEY.
2. NUMERIC KEYPAD.
3. BATTERIES
COMPARTMENT
3
WARNING:
For your own security, it is recommended to
change the opening code while the safe door
is open. If you introduce a wrong number, you
can press the * key to delete it.
3.1. CHANGING MASTER CODE
• Press the * key + ENTER
• Press the 1 key + ENTER
• Enter the initial master code 123456 and press ENTER
• Enter the new master code (4 digits minimum and 6 digits
maximum) and press ENTER
• Repeat the new master code and press ENTER
3.2. PROGRAMMING USER CODE (using the master-code)
• By default the safe is supplied with user code deactivated.
• Press the * key + ENTER
• Press the 2 key + ENTER
• Enter the valid master-code (1-2-3-4-5-6 if original one has
not been changed in advance) and press ENTER
• Enter the user code (4 digits minimum and 6 digits
maximum) and press ENTER.
• Repeat the user code and press ENTER
3.3. CHANGING USER CODE (without using master-code)
The change of the user code without using the master code is
possible only if the user code was set in advance by using the
master code.
• Press the * key + ENTER
• Press the 3 key + ENTER
• Enter the valid user-code and press ENTER
• Enter the new user code (4 digits minimum and 6 digits
maximum) and press ENTER
• Repeat the new user code and press ENTER.
3.4. DELETING USER CODE (with master-code)
• Press the * key + ENTER
• Press the 0 key + ENTER
• Enter the valid master-code and press ENTER
• The user code is deleted.
If the new code is entered correctly, 2 beeps souds and
a green LED flashes. Otherwise, 3 beeps sound warning
that the operation was not succesfull, so the initial
code remains saved. Repeat again the operation.
During operation if you enter a wrong number of digits,
a red LED flashes warning about the error. After an
error is made, start the programming again by pressing
ENTER or the * key.
En

Publicidad

Tabla de contenido
loading

Tabla de contenido