Cleaning And Maintenance - FALMEC Quantum Pro Easy Manual De Instrucciones

HOOD TOUCH PUSHBUTTON PANEL
ON/OFF
Short pulse: Hood switch ON/OFF
Long pulse: Hood operation automatic cycle activation (A) accor-
ding to plate power.
Speed increase from 1 to...9 (up to "P").
Speed "P": active only for a few minutes, then speed 9.
Speed decrease from P to 1.
With hood active (short pulse): TIMER (flashing red LED)
Automatic switch-off after 15 min.
The function is disabled (red LED OFF) if:
- The motor is switched off (button
- Press the TIMER button
With the hood OFF (long pulse 4s):
opening the fins for hood and metal filter maintenance
CARBON.ZEO FILTER ALARM
Maintenance after approximately 2000 hours of operation.
The display shows alternating with the hood speed.
To reset the alarm: with the motor running, press the
for 5 seconds.
The display shows for 2 seconds.
To activate the alarm:
With the hood off, press the
The display shows .
Press the key to activate the alarm, the display shows
with the dot in the top left-hand corner flashing.
Wait 3 seconds, the configuration is saved
To deactivate the alarm:
With the hood off, press the
The display shows .
Press the key to deactivate the alarm, the display shows
with the dot in the top left-hand corner switched off.
Wait 3 seconds, the configuration is saved.
If the pushbutton panel is completely inactive, before contacting
the Technical assistance service, disconnect power temporarily to
the appliance (about 5"), possibly by acting on the main switch, to
restore normal operation. If this measure has no effect, contact the Techni-
cal assistance service.
).
again .
key
and keys for 5 seconds
and keys for 5 seconds,

CLEANING AND MAINTENANCE

ATTENTION!
For cleaning, never use a steam equipment.
Before cleaning the cooker, make sure that it is at room temperature.
Always clean the cooker after each use with a specific cleanser for pyroceram.
Do not use products containing:
- corrosive agents (soda, acids, ammoniac).
- abrasive agents (dusts or paste).
Do not wash the flaps in a dishwasher.
Do not use pointed or abrasive objects.
After cleaning, dry the appliance with a soft cloth.
USEFUL CARE TIPS
Clean your glassceramic cooktop regularly, preferably every time you use it.
Avoid using abrasive sponges or scouring agents.
Harsh chemical cleaners like oven sprays or stain removers are also unsuitable, as
are bathroom or household cleaners.
Accidents happen ...
Do not allow the hot hob to come into contact with plastic, tin foil, sugar or
sugary food have fallen on the hot glass-ceramic cooktop. Please scrape it off
the hot surface as quickly as possible. If these substances melt, they can damage
the glass-ceramic cooktop.
Sparkling results in only three steps:
To thoroughly clean your glass-ceramic cooktop, first remove dirt and food with
a suitable metal scraper.
Once the glass-ceramic cooktop has cooled, put a few drops of a suitable clean-
er on it and rub it on with a paper towel or a clean cloth.
Then wipe the glass-ceramic cooktop with a damp cloth and dry it with a clean
cloth.
How do I identify a suitable glass-ceramic scraper?
• Scraper made of metal (won't melt or catch fire)
• Scraper easy to lock / to unlock
• Blade is fixed precisely, it does not shift
• Blade is unbroken, clean and stainless
• Scraper certified by testing institute, if procurable (e.g. TÜV-GS seal)
• User manual and safety instructions available
CLEANING OF INTERNAL SURFACES
Do not clean electrical parts, or parts related to the motor inside
the hood, with liquids or solvents.
For the internal metal parts, see the previous paragraph.
METAL ANTI-GREASE FILTERS
It is advised to frequently wash the metal filters (F) (at least once a month)
leaving them to soak in boiling water and cleaning solution for 1 hour, taking
care not to bend them.
Do not use corrosive, acid or alkaline detergents.
Rinse them well and wait for them to be completely dry before reassembling
them.
Washing in a dishwasher is permitted.
To extract and insert the metal anti-grease filters see the assembly instructions.
CARBON AND ZEOLITE FILTERS (OPTIONAL) KACL.963
In normal use conditions, we recommend regenerating the zeolite-carbon filter
every 18 months and replacing it after 3 years. Simply place it in a domestic oven
at a temperature of 200°C for approximately 1 hour to regenerate it.
Wait until the filter cools before reassembling it.
GREASE DRIP TRAY
It is advisable to clean the tray every 1 month.
Do not use corrosive, acid or alkaline detergents.
For more thorough cleaning, remove the oil collection tray (see figure) and wash
it with water and washing up liquid. Rinse it well and wait for it to be completely
dry before reassembling it.
27