Prior To Initial Operation; Replacing The Blade; Adjusting The Cutting Depth - SPARKY TK 65 Instrucciones De Uso Originales

18(a). Blade screw (TK 65)
18(b). Blade bolt (TK 85)
19. Blade
20. Blade guard lever
21. Depth adjustment lever
22. Dust extraction port
23. Back handle
24. Rip fence
25(a). Blade hex key (TK 65)
25(b). Blade spanner (TK 85)
VII - Operation
This power tool is supplied from single-phase alternat-
ing current mains only. It is double insulated according
to EN 60745-1 and IEC 60745 and can be connected
to grounded or not grounded sockets. This power tool
is radio suppressed in compliance with EMC Directive
2004/108/EC.
This power tool is designed for longitudinal and cross
sawing wood in a straight line at bevel angle from 0° to
45°.

PRIOR TO INITIAL OPERATION

▪ Make sure the power supply voltage corresponds to
the value indicated on the name plate with technical
data of the tool.
▪ Always check the position of ON/OFF switch. The
power tool must be connected to the power supply
socket only when this switch is in OFF position. If the
plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
▪ Make sure that the cord and the plug are in order. If the
replacement of the supply cord is necessary, this has
to be done by the manufacturer or his agent in order
to avoid a safety hazard.
▪ Always inspect the blade. Use only well grinded
blades. Never use blades with cracks and indents or
HSS-blades.
▪ Check if the mobile guard moves freely.
▪ Make sure the work piece or the material is well se-
cured.
WARNING: Always switch off and unplug the
power tool prior to any adjustment, servicing or main-
tenance or in case of mains drop-out.

REPLACING THE BLADE

WARNING: Unplug the power tool!
1. Press the spindle lock button (3).
TK 65
Whilst depressing the spindle lock button (3), turn the
blade hex key (25a) anti-clockwise and remove blade
screw (18a) and outer blade flange (16). (Fig. 1a)
Original instructions
pages_TK 65-85-2012.indd 7
All manuals and user guides at all-guides.com
2. Ensure blade flanges and bolt is clean of sawdust,
3. Retract the lower blade guard (15) all the way up into
4. Make sure the saw teeth and arrow on the blade (19)
5. Slide blade (19) through slot in the base plate (14)
6. Fit outer blade flange (16).
7. Before connecting the saw to a power source, en-
NOTE: Do not modify blade hex key/spanner (25a/b)
to elongate it, since it may lead to over tightening of the
blade screw/bolt (18).

ADJUSTING THE CUTTING DEPTH

Loosen the depth adjustment lever (21). Hold the base
plate (14) down with one hand and raise or lower the saw
by the back handle (23). Tighten depth adjust lever (21) at
the depth setting desired. Check desired depth. (Fig. 3)
To obtain minimum splintering while operating, ensure
that no more than one tooth protrudes through the tim-
ber.
ADJUSTING THE BEVEL
Vertical cutting
Set the base plate (14) to maximum depth of cut setting.
Loosen bevel adjustment knob (10), set to 0º on bevel
scale (9), retighten bevel adjustment knob (10) and check
TK 85
Whilst depressing the spindle lock button (3), turn
the blade spanner (25b) anti-clockwise and remove
blade bolt (18b) and outer blade flange (16). (Fig. 1b)
grease, etc.
the upper blade guard (5). While retracting the lower
blade guard (15), check operation and condition of
the lower guard spring. (Fig. 2)
point in the same direction as the arrow on the upper
blade guard (5).
and mount it against the inner blade flange (17) on
the shaft. Make sure the large diameter of the blade
flanges lay flush against the blade (19).
TK 65
First tighten blade screw (18a) to finger tight. Engage
spindle lock button (3).
Whilst depressing the spindle lock button (3), tighten
blade screw (18a) firmly with the blade hex key (25a)
supplied.
TK 85
First tighten blade bolt (18b) to finger tight. Engage
spindle lock button (3).
Whilst depressing the spindle lock button (3), tighten
blade bolt (18b) firmly with the blade spanner (25b)
supplied.
sure that:
- The spindle lock button (3) is released;
- The blade (19) rotates freely;
- The lower blade guard (15) operates correctly.
WARNING: Unplug the power tool!
WARNING: Unplug the power tool!
7
EN
6.8.2012 . 08:40:01 .