Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
EN
Table of Contents
1.
Introduction .................................................................................................................................................... 49
1.1.
Preface ............................................................................................................................................................ 49
1.2.
Contact ........................................................................................................................................................... 49
1.3.
Scope of delivery ............................................................................................................................................. 49
2.
Control unit description ................................................................................................................................... 50
2.1.
Product features .............................................................................................................................................. 50
2.2.
Technical information ....................................................................................................................................... 50
2.3.
Control unit overview ....................................................................................................................................... 51
2.4.
Connector features .......................................................................................................................................... 52
2.4.1.
CPC 14 connector (ST 630 only) ..................................................................................................... 52
2.4.2.
CPC 19 connector (ST 632 only) ..................................................................................................... 52
2.5.
Plug pin assignment (ROHDE default) .............................................................................................................. 53
2.5.1.
CPC 14 connector (ST 630 only) ..................................................................................................... 53
2.5.2.
CPC 19 connector (ST 632 only) ..................................................................................................... 53
2.5.3.
Special Notes .................................................................................................................................. 53
2.6.
Kiln contactor protection circuit ....................................................................................................................... 54
3.
Safety instructions........................................................................................................................................... 54
3.1.
General notes .................................................................................................................................................. 54
3.2.
General safety notes ........................................................................................................................................ 54
4.
Mounting ........................................................................................................................................................ 55
4.1.
General safety note ......................................................................................................................................... 55
4.2.
Mounting the bracket ...................................................................................................................................... 55
4.3.
Connecting the connection cable .................................................................................................................... 56
4.4.
Control unit extension cable ............................................................................................................................ 56
4.5.
Third-party kiln note ......................................................................................................................................... 56
5.
Installation ...................................................................................................................................................... 56
5.1.
Switching the control unit on & off ................................................................................................................... 56
5.2.
Quick start guide ............................................................................................................................................. 57
6.
Operation & use .............................................................................................................................................. 57
6.1.
Display screens after switching on ................................................................................................................... 57
6.2.
Keylock ........................................................................................................................................................... 58
6.3.
Temperature display ........................................................................................................................................ 58
6.3.1.
Temperature display for single zone kilns ......................................................................................... 58
6.3.2.
Temperature display for multi zone kilns .......................................................................................... 59
6.3.3.
Assigning the heating zones ............................................................................................................ 59
6.4.
Firing segments ............................................................................................................................................... 59
6.4.1.
Explanation of firing segments ......................................................................................................... 59
6.4.2.
Example of a firing program to illustrate the firing segment .............................................................. 60
6.5.
Programming the control unit .......................................................................................................................... 62
6.5.1.
Changing the firing program ............................................................................................................ 62
6.5.2.
Changing a heating ramp into a cooling ramp ................................................................................. 64
6.5.3.
Changing a cooling ramp into a heating ramp ................................................................................. 65
6.5.4.
Programming the "FULL" ramp rate ................................................................................................. 66
6.5.5.
Programming the "END" ramp rate .................................................................................................. 67
7.
Programming the additional switch output (ST 632 only) ................................................................................... 68
7.1.
General description (ST 632 only) .................................................................................................................... 68
7.2.
Parameters for switch outputs (ST 632 only) .................................................................................................... 68
7.3.
Assignment of the switch outputs (ST 632 only)............................................................................................... 68
7.4.
Program switch outputs (ST 632 only) ............................................................................................................. 68
8.
Instructions for use ......................................................................................................................................... 70
8.1.
Firing ............................................................................................................................................................... 70
8.1.1.
General operation ............................................................................................................................ 70
8.1.2.
8.1.3.
Program delay ................................................................................................................................. 71
8.1.4.
Program advance facility ................................................................................................................. 71
Instruction Manual ST 630/ST 632
................................................................................................................... 70
47 / 317 - EN -
Publicidad
Tabla de contenido
