Cleaning And Maintenance - Chicco Gro-up 123 Manual Del Usuario

9. Fit the booster cushion by fastening the holes to the di-
agonal belt routings (Fig.14).
WARNING! The booster cushion is to be used up to about
11 kg.
10. Make sure your child is seated comfortably in the child
car seat, adjust the harness straps around the child's
body without pulling them too tight, join the two har-
ness straps (Fig. 15) and click them into the buckle (Fig.
15A).
11. Use the adjustment knob A fitted at the top of the back-
rest to adjust the height of the child car seat's headrest
(Fig. 16), so as to allow the harness straps to come out at
the height of the child's shoulders (Fig. 17).
12. To tighten the restraint harnesses of the child car seat,
pull the adjustment strap I until it is correctly fitted to
the child's body (Fig. 18).
13. Check that the child car seat is fastened correctly (Fig.
19).
14. To remove the child from the child car seat, press the
button on the buckle and release the harness straps
(Fig. 20)
5. CHANGE OF CHILD CAR SEAT SET-UP FROM GROUP
1 (9-18 KG) TO GROUP 2/3 (15-36 KG)
To change the set-up of the child car seat from Group 1 to
Group 2-3, continue as follows:
1. Release the child car seat harnesses from the buckle (Fig.
21)
2. Turn the knob to raise the headrest as much as possible
and loosen the incorporated harness straps as much as
possible (Fig. 22).
3. If present, remove the booster cushion by releasing it
through the belt routings (Fig. 6).
4. Remove the backrest lining (Fig. 23) and unfasten the flap
behind the backrest (Fig. 24).
5. Run the incorporated harness straps under the diago-
nal strap routings (Fig. 25) and push the shoulder straps,
harness and relevant ends through the relevant holes
(Fig.26).
6. The harness straps must be as illustrated in figure 27 after
this step.
7. Release the buckle from the crotch strap protection and
fit it in the compartment below it (Fig. 28); fit the crotch
strap protection in the same hole (Fig. 29).
8. Fit the flap behind the backrest again and apply the lin-
ing to the structure.
6. FITTING THE CHILD CAR SEAT IN THE CAR AND
SEATING THE CHILD IN GROUP 2/3 (15-36 KG)
1. Place the child car seat onto the chosen forward-facing
car seat (Fig. 30)
2. Run the diagonal section of the seat belt behind the
headrest and through the relevant red belt routing (C)
under the headrest. Place your child carefully into the car
seat, and check that the child is sitting with his back cor-
rectly against the backrest of the child car seat.
3. Fasten the car seat belt in the buckle so that both the
waist and the diagonal sections of the belt pass in the
waist belt routings L (Fig. 31).
4. When adjusting the headrest, check that the position of
the diagonal seat belt guide (B) is positioned over the
shoulder at a distance of no more than 2 cm (Fig. 32).
5. Pull the diagonal car safety belt strap towards the retrac-
tor, to ensure the belt is tight and fitting properly over the
child's legs and chest (Fig. 33).
6. Check that the child car seat is fastened correctly (Fig. 34).
WARNING!
• Always check that the seat belt is distributed evenly in all
points and that it is not twisted.
• Check that the diagonal seat belt fits correctly across the
child's shoulder and does not press on the child's neck. If
necessary, adjust the headrest.
• Check that the car safety belt retractor is behind the back-
rest of the car seat (Fig. 35).
To remove a child from a Group 2 and 3 child car seat:
1. Release the car safety belt from its buckle.
2. Remove the car safety belt from the child's body.
3. Carefully remove the child from the car seat.
WARNING! If you do not intend to remove the child car
seat from the vehicle, fasten the car seat belts back into the
buckle, so that the child car seat remains fastened safely
inside the vehicle even without the child; this will avoid
danger during an accident or sudden braking of the car.
7. REFITTING THE HARNESS FOR SEATING IN GROUP
1 (9-18 KG)
Follow the instructions illustrated in sections 5 and 6 in the
opposite order.
8. ADJUSTING THE HEIGHT OF THE HEADREST
The height of the headrest can be adjusted to better adapt
the child car seat to the height of the child. When it is cor-
rectly adjusted, it ensures:
- That the child's head is always held in place and well pro-
tected (Gr. 1-2-3).
- That the child car seat safety harnesses are always at the
right height, that is the shoulder height (Gr. 1)
- That the diagonal car seat belts are always at the right
height with the belt routings incorporated in the headrest
C (Gr. 2-3).
To adjust the height of the headrest, turn the knob A fit-
ted at the top of the backrest until you reach the required
height (Fig. 16).
9. RECLINING
The child car seat has just one reclinable position.
To recline the child car seat, use the handle and slightly lift
the child car seat to change to reclined position (Fig. 36).
We recommend reclining the seat before seating the child.
WARNING: Make sure that the reclining system locks in
place by checking that the handle K returns back to place.
WARNING: After making the adjustments, make sure that
the harnesses are well tensioned.

10. CLEANING AND MAINTENANCE

HOW TO CLEAN THE FABRIC COVER
The child Car seat's fabric cover can be removed and
cleaned by hand or in a washing machine at 30°C. Please
refer to the cleaning instructions on the fabric label, which
illustrates the following washing symbols:
Machine washable at 30°C.
14
Ne
no
wi
the
ins
1.
2.
3.
4.
5.
6. T
t
7.
8.
To
ins
HO
Cle
on
Th
no
CH
It i
fol
or
• Fa
fro
m
• H
th
th
ju
• P
d
WA
wo
ma
ST
Wh
the
an
DI
Wh
na
ap
en
co