Pioneer KRP-500A Manual De Instrucciones página 7

Important user information
Display panel protection function
When still images (such as photos and computer images) stay on
the screen for an extended period of time, the screen will be slightly
dimmed. This is because the protection function of the display
panel automatically adjusts the brightness to protect the screen
when detecting still images; so this does not designate
malfunction. The screen is dimmed when a still image is detected
for about three minutes.
Information of pixel defect
Plasma television displays information using pixels. Pioneer flat
screen TV panels contain a very large number of pixels (over 6.2
million pixels for a 50 inch display). All Pioneer display panels are
manufactured using a very high level of ultra-precision technology
and undergo individual quality control.
In rare cases, some pixels can be permanently switched off, or on,
resulting in either a black or colored pixel permanently fixed on the
screen.
This effect is common to all plasma television because it is a
consequence of the technology.
If the defective pixels are visible at a normal viewing distance of
between 2.5 meters and 3.5 meters while viewing a normal
broadcast (i.e. not a test card, still image or single color display)
please contact the supplying dealer.
If, however, they can only be seen close up or during single color
displays then this is considered normal for this technology.
Infrared rays
The display panel releases infrared rays because of its
characteristics. Depending on how the flat screen TV is in use, the
remote controls of nearby equipment may be adversely affected or
wireless headphones using infrared rays are interfered by noise. If
this is the case, place that equipment at a location where its
remote control sensor is not affected.
Radio interference
While this product meets the required specifications, it emits a
small amount of noise. If you place such equipment as an AM
radio, personal computer, and VCR close to this product, that
equipment may be interfered. If this happens, place that
equipment far enough from this product.
Display panel driving sound
The screen of the display panel is composed of extremely fine pixels
and these pixels emit light according to received video signals. This
principle may make you hear buzz sound or electrical circuit
humming from the display panel.
Do not attach such items as labels and tape to the product
This may result in the discoloration or scratch of the cabinet.
When not using the product for a long period of time
If you do not use the product for a long period of time, the functions
of the product may be adversely affected. Switch on and run the
product occasionally.
All manuals and user guides at all-guides.com
Condensation
Condensation may take place on the surface or inside of the
product when the product is rapidly moved from a cold place to a
warm place or just after a heater is switched on in winter morning,
for example. When condensation takes place, do not switch on the
product and wait until condensation disappears. Using the product
with condensation may result in malfunction.
Cleaning the surface of the screen
When cleaning the screen surface, gently wipe it with the supplied
dry cleaning cloth.
Rubbing hard on the screen can scratch the special film coating
the surface. If cleaning gently with the dry cloth is not enough to
remove grime, unplug the power cord from the outlet and follow
the procedure below.
1. Soak a piece of soft, untreated cloth in distilled water.
2. Wring out the cloth so that it is slightly damp, not wet.
3. Gently wipe the surface of the screen with the damp cloth.
4. Wipe the surface again using the dry cloth included with your
Cleaning the glossy surface of the front cabinet
When cleaning the glossy surface of the front cabinet, gently wipe
it with a dry soft cloth; the supplied cleaning cloth or other similar
cloths (e.g., cotton and flannel). If you use a dusty or hard cloth or
if you rub the cabinet hard, the surface of the product will be
scratched.
The cabinet of this product is mostly composed of plastic. Do not
use chemicals such as alcohol, benzene, thinner or insecticides to
clean the cabinet. Using these chemicals may result in quality
deterioration, discoloration or coating removal.
Do not expose the product to volatile gas or fluid such as pesticide.
Do not make the product contact with rubber or vinyl products for
a long period of time. The effect of plasticizer in the plastic may
result in quality deterioration or coating removal.
If you clean the surface of the cabinet with a wet cloth, water
droplets on the surface may enter into the product, resulting in
malfunction.
Caution
A "treated" cloth contains polish or other chemicals, such as in a
commercially available eyeglass cleaning towelette.
Make sure to wring out the cloth completely. Cleaning the surface
with a wet cloth can allow water to seep into the unit, causing
damage.
panel to remove any remaining dampness and to prevent
streaks.
01
7
En