Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
4.2.3.2 HOW TO PROGRAM THE INTERCOM FUNCTION
Example:
key = general intercom to user code 3
√
Take note of the S1 setting and restore it when programming is complete
1
Enter programming mode
„ Set S2 DIP switch 5-6 to the combination 01
» the Privacy LED flashes
2
2.1 Choose the function: refer to the
combination in which the intercom function (INT) is listed for the keys you wish to program.
2.2 Addressing:
„ for internal intercom set S1 DIP switches with the same user code of the internal unit.
„ for general intercom to another user code set S1 DIP switches with the desired
address see page
3
Select the key to be associated with the function
„ Press and release the key to be associated with the function
» the lock-release LED lights up
» a confirmation tone will sound.
4
Exit programming mode
„ To exit programming mode, set S2 DIP switches 5-6 to the combination 00
» the Privacy LED switches off
5
When programming is complete,
„ Set S2 DIP switches 1-2-3-4 to the combination 1111 (PROG setting). In this DIP switch
setting, the keys control the programmed functions; the NON-programmed keys control
functions referred to on line 0000
„ Restore the user code setting on S1
4.2.3.3 HOW TO PROGRAM THE PAGING FUNCTION
Example:
key = general paging to user code 3
√
Take note of the S1 setting and restore it when programming is complete
1
Enter programming mode
„ Set S2 DIP switch 5-6 to the combination 01
» the Privacy LED flashes
2
2.1 Choose the function: refer to the
combination in which the paging function (PAG) is listed for the keys you wish to program.
2.2 Addressing:
„ for internal paging set S1 DIP switches with the same user code of the internal unit.
„ for general paging to another user code set S1 DIP switches with the desired address
(see page
27 "TAB. A" ).
3
Select the key to be associated with the function
„ Press and release the key to be associated with the function
» the lock-release LED lights up
» a confirmation tone will sound.
4
Exit programming mode
„ To exit programming mode, set S2 DIP switches 5-6 to the combination 00
» the Privacy LED switches off
5
When programming is complete,
„ Set S2 DIP switches 1-2-3-4 to the combination 1111 (PROG setting). In this DIP switch
setting, the keys control the programmed functions; the NON-programmed keys control
functions referred to on line 0000
„ Restore the user code setting on S1.
"Preset function"
table and select a S2 DIP switches
27 "TAB. A" .
(21 "4.2.1 Preset function"
"Preset function"
table and select a S2 DIP switches
("Preset
function"table).
table)
ON
1 2 3 4
5
6 7
8
Example: 0100
ON
1 2 3 4
5
6 7
8
ON
1 2 3 4
5
6 7
8
ON
1 2 3 4
5
6 7
8
ON
1 2 3 4
5
6 7
8
ON
1 2 3 4
5
6 7
8
ON
1 2 3 4
5
6 7
8
Example: 0100
ON
1 2 3 4
5
6 7
8
ON
1 2 3 4
5
6 7
8
ON
1 2 3 4
5
6 7
8
ON
1 2 3 4
5
6 7
8
ON
1 2 3 4
5
6 7
8
23
Publicidad
Tabla de contenido
