Description; Technical Description; Data Plate; Standard Equipment - Saf-Fro FILCORD 353C Instrucciones De Seguridad, Empleo Y Mantenimiento

EN
1.0 DESCRIPTION AND TECHNICAL DESCRIP-
TION
1.1

DESCRIPTION

MIG/MAG welding professional generators, three-phase feeding,
forced ventilation, prepared for separated wire pulling set.
1.2

TECHNICAL DESCRIPTION

DATA PLATE

PRIMARY
Three phase supply
Frequency
Effective consuption
Maximum consuption
SECONDARY
Open circuit voltage
Welding current
Duty cycle 35%
Duty cycle 60%
Duty cycle 100%
Protection class
Insulation class
Weight
Dimensions
European Standards
350A S and 350A S(W)
PRIMARY
Three phase supply
Frequency
Effective consuption
Maximum consuption
SECONDARY
Open circuit voltage
Welding current
Duty cycle 35%
Duty cycle 60%
Duty cycle 100%
Protection class
Insulation class
Weight
Dimensions
European Standards
1.3

STANDARD EQUIPMENT

- Earth cable
1.4

DUTY CYCLE AND OVERHEATING

The duty cycle is the percentage of a 10 minute period for which
the welder can continue to weld without overheating. If the ma-
chine overheats, the welding current is shut off and the relative in-
dicator lamp illuminates. In this case, leave the machine to cool for
approx. 15 minutes and, before restarting, lower the welding cur-
rent value and relative voltage or reduce the work time.

DESCRIPTION AND TECHNICAL DESCRIPTION

350A C
230 V (+/- 10%) 400 V (+/- 10%
50 Hz
25 A 14,2 A
42 A 24 A
18 ÷ 45 V
35 A ÷ 350 A
350 A
270 A
210 A
IP 23
H
Kg. 116
mm 620 x 940 x 1000
EN 60974.1 / EN 60974.10
230 V 400 V
50 Hz
25 A 14,2 A
42 A 24 A
18 ÷ 45V
35 A ÷ 350 A
350 A
270 A
210 A
IP 23
H
Kg. 100
mm 500 x 865x 900
EN 60974.1 / EN 60974.10
Example: 400 A - 60% means working for 6 minutes at 400 A with
4 minutes rest time.
1.5

VOLT - AMPERE CURVES

The volt-ampere curves show the welder's maximum output cur-
rents and voltage (see page X).
2.0

INSTALLATION

IMPORTANT: BEFORE CONNECTING, PREPARING OR US-
ING EQUIPMENT, READ SAFETY PRECAUTIONS.
2.1

MACHINE ACCESSORIES

1. Unpack the equipment and components to complete the ma-
chine assembly.
2. Leave the machine on the wood pallet (if used) or lift it after
fitting the special eye-bolts. With a 13 hex wrench to remove
the eight screws (four on the left and four on the right) under
the front panel; fit the two castor wheels and refit the screws.
3. Remove the two screws securing the machine to the pallet,
located on the cylinder support.
4. Raise the rear section of the machine slightly to rotate the
pallet and thus release the rear section.
5. Remove the screws from the axle and proceed with assem-
bly of the fixed wheels.
6. Fit the handles.
7. Assemble the pulling set stand using the four screws provid-
ed on the top centre of the generator cover.
8. Remove the pulling set packaging and position it on the stand
as soon as it is assembled. Make sure that the two stands are
coupled.
9. Connect the multi polar plug and the umbilical cord power
plug to the appropriate generator sockets.
3 EN