Wahl 3616 Manual Del Operador página 11

Average active efficiency: 75.58 %
No-load power consumption: 0.06 W
Operating conditions
Ambient temperature: 0°C - +40°C
The appliance is safety insulated and radio screened. It meets
the requirements of EU Electromagnetic Compatibility Directive
2014/30/EU and Low Voltage Directive
2014/35/EU.
Operation
Preparation
Keep the packaging material for safe storage or trans-
port later.
f Check that the contents are complete.
f Check all the parts for possible transport damage.
Safety
Caution! Damage due to incorrect power supply.
f Only operate the appliance with the voltage stated
on the nameplate.
Charging the battery
1. Switch off the appliance using the on/off switch (Fig. 3ⓑ).
2. Connect the appliance plug on the plug-in transformer to the
appliance socket (Fig. 2ⓐ).
3. Connect the plug-in transformer to the mains socket (Fig. 2ⓑ).
The charging process starts.
·
During charging, the charging indicator shines red.
·
In order to ensure a long operating life of the battery
pack, it should always be completely empty prior to
recharging.
Battery operation
1. Switch on the appliance using the on/off switch, and switch off
after use (Fig. 3ⓐ/ⓑ).
Operation
Foil shave
1. Remove the protective cap.
2. Switch on the appliance using the on/off switch (Fig. 3ⓐ).
3. Gently guide the shaver upward against the skin surface and
shave against the direction of the beard growth (Fig. 9). At the
same time, pull the skin tight with your free hand so that the
stubble stands up.
Caution! Damage due to incorrect operation.
f Avoid too much pressure on the shaver foil; this
could lead to foil breakages.
4. Use the on/off switch to switch off the appliance after use
(Fig. 3ⓑ).
5. Place the protective cap back onto the device.
Maintenance
Warning! Injuries and material damage due to incor-
rect handling.
f Switch off the appliance before cleaning it or per-
forming any maintenance and disconnect it from
the mains.
Cleaning and care
Danger! Electric shock due to penetration of liquid.
f Do not immerse the appliance in water!
f Do not allow any liquid to get inside the appliance.
Caution! Danger from aggressive chemicals.
Aggressive chemicals could damage the appliance and
accessories.
f Never use solvents or scouring agents.
Caution! Damage from incorrectly cleaning the
shaver foil.
Never clean the shaver foil with the cleaning brush
because this could damage the shaver foil.
f Tap the shaving head with the shaver foil on a level
surface and blow off the hair.
·
Accessories are available from our dealer.
·
Spare parts are available from our service centre.
f Remove the shaving head from the housing (Fig. 4). Tap the
shaving head with the shaver foil on a level surface and blow
off the hair. Remove the hair clippings from the cutter with the
cleaning brush (Fig. 5).
f Only wipe the appliance with a soft, slightly damp cloth.
f Reattach the protective cap after cleaning.
If the shaving performance deteriorates after long use
despite regular cleaning, the cutter and the shaver foil
should be replaced.
Replacing the cutter and the shaver foil
1. Remove the protective cap from the shaving head.
2. Remove the shaving head with shaver foil (Fig. 4).
3. Pull the shaver foil out of the shaving head (Fig. 6).
Caution! Damage from incorrectly handling the
shaver foil.
f Only touch the new shaver foil from the side.
f The shaver foil may only be bent and not folded.
4. Push the shaver foil into the shaving head to the limit stop
(Fig. 7).
5. Grip the side of the cutter and carefully remove it from the
holder (Fig. 8ⓐ).
E N G L I S H
de
en
fr
it
es
pt
nl
da
sv
no
fi
tr
pl
cs
sk
hr
hu
sl
ro
bg
ru
uk
et
lv
lt
el
11
ar