Publicidad
Idiomas disponibles
Idiomas disponibles
doing so could trigger a sudden recoil with a high reactive force.
Determine why the insertion tool stalled and rectify this, paying
heed to the safety instructions.
Possible causes may be:
• it is tilted in the workpiece to be machined
• breakage of the material to be used
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool is sharp-edged and can become hot during use.
WARNING! Danger of cuts and burns
-
when handling the insertion tools
-
when setting the device down
Wear protective gloves when handling insertion tools.
Chips and splinters must not be removed while the machine is
running.
Always disconnect the plug from the socket before carrying out
any work on the machine.
OPERATION
Cold Starting
GB
If this tool is stored for a long period of time or at cold tempera-
tures, it may not hammer initially because the lubrication has
become stiff.
To warm up the tool
1. Insert and lock a bit or chisel into the tool.
2. Pull the trigger and apply force to the bit or chisel against a
concrete or wood surface for a few seconds. Release the trigger.
3. Repeat until the tool starts hammering. The colder the tool is,
the longer it will take to warm up.
SPECIFIED CONDITIONS OF USE
The hammer can be used for chiselling in stone and concrete.
MAINS CONNECTION
Appliances used at many different locations including wet room
and open air must be connected via a residual current device (FI,
RCD, PRCD) of 30mA or less.
Connect only to single-phase AC system voltage as indicated on
the rating plate. It is also possible to connect to sockets without an
earthing contact as the design conforms to safety class II.
Only plug-in when machine is switched off.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
If the supply cord of this appliance is damaged, it must only be
replaced by a repair shop appointed by the manufacturer, to avoid
hazardous situations.
Use only Milwaukee accessories and Milwaukee spare parts.
Should components need to be replaced which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on the
label and order the drawing at your local service agents or directly
at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Win-
nenden, Germany.
English
SYMBOLS
Please read the instructions carefully before starting the
machine.
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket before carrying
out any work on the machine.
Always wear goggles when using the machine.
Wear ear protectors.
Wear a suitable dust protection mask.
Wear gloves!
Accessory - Not included in standard equipment.
Do not dispose of waste electrical and electronic equipment
as unsorted municipal waste. Waste electrical and electronic
equipment must be collected separately. Waste light sources
have to be removed from equipment. Check with your local
authority or retailer for recycling advice and collection point.
According to local regulations, retailers may have an obliga-
tion to take back waste electrical and electronic equipment
free of charge. Your contribution to re-use and recycling of
waste electrical and electronic equipment helps to reduce
the demand of raw materials. Waste electrical and electronic
equipment contain valuable, recyclable materials, which can
adversely impact the environment and the human health, if
not disposed of in an environmentally compatible manner.
Delete personal data from waste equipment, if any.
Class II tool. Tool in which protection against electric
shock does not rely on basic insulation only, but in which
additional safety precautions, such as double insulation
or reinforced insulation, are provided. There being
no provision for protective earthing or reliance upon
installation conditions.
n
No-load speed
0
V
Voltage
AC Current
European Conformity Mark
British Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfills all the relevant provisions
of the directives
2011/65/EU (RoHS)
2006/42/EC
2014/30/EU
and the following harmonized standards have been used
EN 62841-1+A11:2022
EN 62841-2-6:2020 +A11:2020
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 61000-3-2:2019+A1:2021
EN 61000-3-3:2013+A1:2019+A2:2021
EN IEC 63000:2018
Measured values determined according to 2000/14/EC at the user's
ear. Conformity assessment procedure according to Annex VI.
EU Notified Body:
DEKRA Testing and Certification GmbH,
Handwerkstraße 15, 70565 Stuttgart
Location Certification Body, Dinnendahlstr. 9, 44809 Bochum,
Germany
Notified Body number: 0158
Measured sound power level: 97,6 dB (A
Guaranteed sound power level: 100,0 dB (A)
Winnenden, 2023-01-20
Alexander Krug / Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility
that the product described under „Technical Data" fulfills all the
relevant provisions of the following Regulations
S.I. 2012/3032 (as amended), S.I. 2008/1597 (as amended),
S.I. 2016/1091 (as amended) and that the following designated
standards have been used:
BS EN 62841-1+A11:2022
BS EN 62841-2-6:2020 +A11:2020
BS EN IEC 55014-1:2021
BS EN IEC 55014-2:2021
BS EN IEC 61000-3-2:2019+A1:2021
BS EN 61000-3-3:2013+A1:2019+A2:2021
BS EN IEC 63000:2018
Measured values determined according to 2000/14/EC at the user's
ear. Conformity assessment procedure according to Annex VI.
EU Notified Body:
DEKRA Testing and Certification GmbH,
Handwerkstraße 15, 70565 Stuttgart
Location Certification Body, Dinnendahlstr. 9, 44809 Bochum,
Germany
Notified Body number: 0158
Measured sound power level: 97,6 dB (A
Guaranteed sound power level: 100,0 dB (A)
Winnenden, 2023-01-20
Alexander Krug / Managing Director
Authorized to compile the technical file
Techtronic Industries (UK) Ltd
Parkway
Marlow SL7 1YL
UK
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
English
GB
Publicidad
