Descargar Imprimir esta página

Taski ULTIMAXX 1900 Manual De Instrucciones página 116

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 124
Cleaning start
• Switch on the machine (Push in the key).
The indicator elements lights up briefly.
• Press the suction unit ON/OFF but-
ton.
The display lights up; the suction en-
gine starts.
• Press the Cleaning solution supply
ON/OFF button.
The display lights up.
The cleaning solution supply is start-
ed when the brushes rotate.
• Select the intended dosing by press-
ing the cleaning solution inflow quan-
tity buttons +/-.
Notice:
Diversey recommends sustainable working by de-
termination of the correct product dosing quantity.
Overdosing or underdosing will lead to unsatisfactory
cleaning results.
• By gently pushing the driving switch
into the direction of movement the
machine is set into motion.
Working with Twister Pad
• Press the Twister ON / OFF button to
use the Twister function.
Upon activation of the Twister button, the following settings are made:
• The lower brush pressure is activated.
• Water level 2 is activated.
(The water level remains individually adjustable.)
• The Slow approach function is activated.
(The slow approach can be switched off and the speed re-
mains individually adjustable)
• The maximum suction performance is activated.
• The IntelliDose function is deactivated.
Power off function
Notice:
The machine turns itself off after 5 minutes when no
longer in use.
During these 5 minutes:
• the brushes may not be manipulated in any way.
• the user must not leave the machine out of sight.
• sucked in or jammed objects may be cleaned from the suc-
tion nozzle only.
• the user is only allowed to leave the machine in order to
clear the work space. The user must maintain visual con-
tact.
114
Battery capacity - end of operational readiness
The battery level indicator provides information on the available oper-
ating time.
• If the red indicator begins to flash, approx. 2 minutes of
working time are left.
• At machines with automatic brush lowering unit, the brush
motor is switched off and the brush unit is automatically
raised.
At machines with foot pedal, the brush motor is switched
off and the brush unit remains on the ground.
• The red display switches to a continuous light.
• Now you have 10 minutes to drive the machine to the
charging station. Then the machine is automatically
switched off.
• In order to restart, the batteries must be fully charged.
Cleaning method
Direct working method:
Scrubbing and suction in one work step.
Indirect working method:
Applying the cleaning solution, scrubbing and suction in several work
steps.
Notice:
In some circumstances, certain combinations of
flooring/soiling and cleaning products may impair
the guiding of the machine.
- Optionally available wheels can improve the ma-
chine's traction on the floor. Please contact your TAS-
KI customer consultant.
Replenishing cleaning solvent
Warning:
The flooring may be damaged when working with-
out cleaning solution.
• The machine must be switched off.
• Open the tank lid.
• Fill the fresh water tank with water, see page 112.
• Add the cleaning product using the dosing cup.
• Close the tank cover.
Draining dirty water
Recovery tank full:
• If the recovery tank is full, the floater
will be sucked onto the suction filter.
This will be indicated by a change of
the noise by increasing the suction
speed as well as residual water at the
bottom.
• Drain the recovery tank, see page 115.
End of operation
• Press the Brush drive ON/OFF but-
ton.
The cleaning solution supply is
stopped.
• Drive on for a few meters so that the brushes keep on ro-
tating for a short time to avoid dripping.
Very important for TASKI contact pads!

Publicidad

loading

Este manual también es adecuado para:

Ultimaxx 2900