LUND 67901 Manual De Instrucciones página 13

GB
PRODUCT OPERATION
Preparing the appliance for operation
Remove the product from its packaging, remove all packaging components, and wash all drive unit components according to the
instructions found in the "Product maintenance" section.
Set the product according to the instructions.
Install the meat grinder attachment body or the grating and shredding attachment body. Mount the body by attaching it to the
mounting socket and then lock it in this position by tightening the knob (II).
Caution! The rear edge of the body has tabs which must fi t into the notches of the socket. The fl ange of the body has a round notch
in which the end of the thread of the clamping screw should fi t.
Ensure the assembly has been correct. A correctly installed attachment body cannot be removed except by unscrewing the lock knob.
Meat grinder attachment
Connect the attachment body to the mounting socket. Insert the grinding auger into the body so that the axis of the drive fi ts into
the opening of the auger (III).
Place the blade on the square socket, the cutting edges should be directed to the outside of the attachment (IV).
Apply the strainer. The strainer has positioning tabs on the edge, which should fi t into the notches in the front of the attachment (V).
The strainers supplied with the product have openings of diff erent sizes. The smaller the openings, the more fi nely the food will
be ground.
Caution! Only one strainer can be fi tted at a time.
Screw the fi xing nut (VI) onto the outlet thread of the attachment.
Install the feed tray on the inlet opening. The feed tray holder has a notch in which the outlet in the fl ange of the inlet opening
(VII) should hit.
Check that the pusher can be easily inserted and removed from the inlet opening.
Sausage-fi lling attachment (IX)
Slide the fi lling attachment into the ring as far as possible. Assemble like the meat grinding attachment, but before screwing on the
fi xing nut, install the sausage-fi lling attachment with ring.
Kebbe attachment (X)
Connect the attachment body to the mounting socket and insert the grinding auger into the body.
The rear part of the kebbe cap is equipped with positioning tabs, which should fi t into the notches in the front of the attachment.
Insert the front part of the socket into the kebbe cap and secure by tightening the fi xing nut.
Grating and shredding attachment (XI)
The attachment has a separate body and a separate pusher.
Install the attachment body into the drive socket.
Slide the drum into the body. The openings in the drum are very sharp and must be handled with care to avoid injury.
The attachment axis tabs should align with the notches in the opening in the rear wall of the drum (XII).
Secure the drum with the attachment ring (XIII). Place the ring on the front part of the attachment body so that the marker on the
front wall of the body shows the symbol of an open padlock. Then rotate the ring so that the marker shows the closed padlock
symbol. Check that the ring cannot be pulled off the attachment body.
Check that the pusher can be easily inserted and removed from the inlet opening.
Caution! Do not use the grinder attachment pusher in this attachment.
The product is equipped with three types of drums. Two drums with round openings are used for grating. The larger the openings,
the larger the shavings. The drum with rectangular openings is used for shredding.
After mounting the selected attachment, place a container under its outlet. The product is ready for use.
Starting the device
Make sure that none of the switches is pressed, press the button marked "STOP & RESET" and then plug the power cord into
the socket.
The product has a switch marked:
"ON", which starts the full speed of the product,
"HALF", which starts half the speed of the product.
The button marked "REVERSE" activates the reverse gear.
The button marked "STOP & RESET" is used to stop the device operation.
Starting the device will take place after pressing the switch marked ON or HALF. The switch does not need to be held in this position.
The device is switched off by pressing the STOP & RESET button. Wait until the motor stops.
O R I G I N A L I N S T R U C T I O N S
13