Loewe klang bar3 mr Guia Del Usuario página 21

Loewe klang bar3 mr

External speakers | Bluetooth Operation
7.9 Factory Reset
Resets the device to the default settings. In standby
mode, press and hold the button for 8 seconds.
"RESET" appears on the display and the device re-
turns to the original settings.
7.10 Software version
To display the current klang bar software version,
press and hold the (Source) button in standby
mode. The software version will appear on the display.
8 External speakers
8.1 External speaker switches
Remove the rear flap of your soundbar before using
the switches.
Use these switches to configure additional external
speakers as SUB / REAR / FRONT / CENTRE chan-
nel. Set the switch to SMALL for small speakers
(120Hz - 20kHz), LARGE for large speakers (20Hz -
20kHz). Setting SUB to LARGE will add +6dB more
sound pressure than SMALL. To disable the speaker
for a specific channel, set the switch to OFF.
8.2 Connecting Loewe Wireless
Digital Audiolink (WDAL
2.0) speakers
You can wirelessly connect up to 6 additional speak-
ers that support WDAL 2.0 to the soundbar. To con-
nect a WDAL 2.0 compatible speaker to the soundbar,
you must:
1. Remove the rear flap on the soundbar and press
and hold the PAIRING button on the soundbar.
2. Press and hold the PAIRING button on the WDAL
2.0 speaker. After successful pairing, "P-OK" will
appear on the display of the soundbar.
3. After successful pairing, configuration of the repro-
duced channel is to be selected on the speaker:
Front left, Front right, Centre, Rear left, Rear right.
Please refer to the speaker manual.
4. Depending on the type of speaker, set the switch on
the back of soundbar corresponding to the selected
speaker to SMALL or LARGE.
Recommended setup for Loewe speakers:
klang mr1: SMALL
klang mr3: LARGE
klang mr5: LARGE
For details on setting the external speaker to pairing
mode, changing its role, and whether to select SMALL
or LARGE on the soundbar switch, please refer to the
user manual of the speaker.
8.3 Connecting wired speakers
Aside from wireless speakers, analogue amplifiers or
active speakers can be connected to the soundbar via
the 6 cinch outputs on the rear. Only active speakers
or external analogue AVRs/amplifiers can be con-
nected to the soundbar. The soundbar is not able to
power passive speakers by itself. Please refer to the
user manual of the amplifier for more information
about connecting passive speakers.
Please connect the speakers to the correct soundbar
outputs according to the speakers position in your
room.
HDMI OUT
TV eARC
1. REAR LEFT (white coloured connector) – connect
rear left speaker
2. FRONT LEFT (white coloured connector) – con-
nect front left speaker
3. SUB – connect a subwoofer
4. CENTER – connect front centre speaker
5. REAR RIGHT (red coloured connector) – connect
rear right speaker
6. FRONT RIGHT (red coloured connector) – con-
nect front right speaker
Depending on the type of speaker, set the switch on
the back of soundbar corresponding to the selected
speaker to SMALL or LARGE.
8.4 Volume offset
If you're experiencing speaker level mismatch, the
soundbar supports different volume offsets for each
channel. You can adjust the overall volume of each
speaker individually:
1. To enter the menu, press and hold
button on the remote control. FL appears on the
soundbar display and the correspondig channel
starts to play reference noise.
2. Use + / - button to change the volume offset of the
selected channel.
3. Use / buttons to select a channel.
4. Switch between all channels and adjust the volume
until all channels are equally loud.
Display abbreviations explained:
FL – front left speaker
FR – front right speaker
SL – rear left speaker
SR – rear right speaker
SUB – subwoofer
CEN – centre speaker
8.5 Distance adjustment
External speakers are usually not evenly spaced
around the listener. For example, the front speakers
may be further away than the rear speakers. Due to a
relatively slow speed of sound, an audio output from
different speakers may reach the listener out of sync.
To avoid this, you can synchronise the speakers by
specifying the distance of each speaker from the lis-
tening position.
Follow these steps to set the distance:
1. Press and hold
onds on the remote control. FL appears on the
soundbar display.
2. Use the + / - button to change the distance of the
selected speaker from the listening position.
3. Use / buttons to select a speaker.
Example: when the display shows "FL3,0", it means
that the current set distance for the left front speaker
is 3 meter. You should now measure the distance from
this speaker to the listening position and adjust it.
For example, if the distance is 2,5 meters, press the +
button until "FL2,5" is displayed. When you have fin-
ished adjusting this speaker, press the
adjust the distance for the next speaker.
Note: In this way, you can also make a correction if
there are echo problems due to different signal pro-
cessing times of the connected devices.
9 Bluetooth Operation
Connect the soundbar to a Bluetooth device (such as
an iPad, iPhone, iPod touch, Android phone, or laptop)
via Bluetooth, and then you can listen to audio files
stored on the device through the soundbar.
1. Press the (Source) button on the unit or re-
mote control repeatedly to switch the soundbar to
BT (Bluetooth) mode.
2. Turn on Bluetooth on the smartphone, search for
and select "klang bar3 mr" to connect. For infor-
mation on enabling Bluetooth, see the user guide
of the Bluetooth device.
3. Wait until you hear the sound from the soundbar.
Select and play audio files or music on your Blue-
(Surround)
tooth device.
Depending on your device, you can press
on the remote control to skip a track or press
to pause/resume playback.
4. To exit Bluetooth, select another source.
When you switch back to Bluetooth mode, the
Bluetooth connection is re-established.
To connect the soundbar to another Bluetooth de-
vice, press and hold the
control to disconnect the currently connected
Bluetooth device.
Note
• The minimum requirements for a Bluetooth device
are: Bluetooth profile A2DP, AVRCP and Bluetooth
version 4.2 + EDR
• The maximum operating range between the sound-
bar and a Bluetooth device is approximately 10
meters.
• Compatibility with all Bluetooth devices is not
guaranteed.
(Equalizer) button for 3 sec-
button and
/
button on the remote
21