Kärcher FC 7 Cordless Manual Del Usuario página 17

● The lowermost LED lights up continuously when the
battery is 1/3 charged, the two upper LEDs continue
to flash.
● When the battery is 2/3 charged, the two lower
LEDs light up continuously, the uppermost LED con-
tinues to flash.
● The battery is fully charged after 4 hours.
● After the battery has been charged, the 3 LED indi-
cator lights remain on constantly for 60 minutes. Af-
ter this time, the LED indicator lights go out.
3. Unplug the charger mains plug from the mains sock-
et after charging.
Illustration E
4. Unplug the charging cable from the device.
Fitting the waste water tank
1. Place the device in the middle of the waste water
tank so that it is positioned between the rollers and
then audibly clicks into place. The position of the
tank is not important because it can be inserted in
both longitudinal directions in the device.
Illustration F
The waste water tank must sit tightly in the device.
Filling the fresh water tank
1. Grasp the fresh water tank by the recessed grips at
the side and remove it from the device.
2. Open the tank cap and turn it to the side.
Illustration G
3. Fill the fresh water tank with cold or lukewarm tap
water.
4. Add KÄRCHER detergent or care agent to the fresh
water tank as required.
ATTENTION
Overdosing or underdosing of the detergent or care
agent
Can result in poor cleaning results.
Follow the dosage recommendations for the detergent
or care agent.
5. Close the tank cap.
6. Fit the fresh water tank into the device.
Illustration H
The fresh water tank must sit tightly in the device.
Operation
General notes on operation
ATTENTION
Moisture
Material damage to sensitive floors
Check the surface to be cleaned for water sensitivity at
an inconspicuous location before using the device.
Do not clean water-sensitive floor coverings such as
e.g. untreated cork floors, since the moisture can pene-
trate and damage the floor.
ATTENTION
Material damage
Damage to the device from pointed, large and/or bulky
objects.
The device must not be stored and used on hard coarse
dirt and objects, as the parts can get stuck under the
waste water tank and cause scratches on the floor and
tank.
Before starting work and storing the device, remove ob-
jects such as shards, pebbles, screws or toy parts from
the floor.
Illustration AI
Note
● To avoid striped patterns, test the device on an in-
conspicuous area before using on sensitive surfac-
es, e.g. wood or fine stone.
● Do not allow it to remain in one area, but keep it in
motion.
● Observe the instructions for the floor covering man-
ufacturer.
Note
Work backwards towards the door so that no footprints
are generated on the freshly washed floor.
Illustration AJ
● Floor cleaning is performed using a to and fro move-
ment at the same speed as when vacuuming.
● Activate the Boost function for heavy soiling. Hold
the Boost function button pressed for this. The roller
speed and water volume are increased when the
boost function is activated. The Boost function can
be activated at cleaning level 1 and cleaning level 2.
The indicator for the corresponding cleaning level
flashes when the Boost function is activated. Allow
the device to slide slowly over the floor without ex-
erting any pressure on the device.
Illustration K
● Various different rollers are available, depending on
the scope of delivery. The colour of the rollers indi-
cates the respective special application for which
they are suitable.
–
Grey / yellow universal rollers: versatile
–
Rollers with black stripes: For cleaning insensi-
tive hard floors (e.g. stone, ceramic); not suitable
for sensitive natural stone floors (e.g. marble, ter-
racotta)
Note
For an optimum cleaning result, wash the rollers in the
washing machine at 60° C before initial use.
ATTENTION
Material damage due to loose rollers
This may damage the washing machine.
Place the rollers in a laundry net and load the washing
machine with extra laundry.
ATTENTION
Uncontrolled motion
Damage to the device and material damage
The cleaning rollers start rotating as soon as the device
is switched on.
Hold the handle tight to prevent the device from moving
away independently.
ATTENTION
Fresh water tank or waste water tank not installed
Material damage
Before starting cleaning work, ensure that the fresh wa-
ter tank is filled with water and the waste water tank is
fitted in the device.
1. Press the ON/OFF switch.
Illustration I
The device switches on.
The cleaning level 1 indicator for normal roller
speed and normal water quantity is lit.
2. Moisten the rollers.
a Hold the Boost function button pressed.
b Move the device back and forth until the rollers
are sufficiently moistened.
English
Starting work
17