Kärcher FC 7 Cordless Manual Del Usuario página 18

Note
If the rollers block immediately after switching on, re-
move the rollers, moisten them under the tap and rein-
sert them.
3. If necessary, switch to cleaning level 2 using the but-
ton for adjusting the cleaning level.
Illustration J
This increases the roller speed and water volume.
The Cleaning level 2 indicator lights up.
Note
Selection of cleaning level 1 or cleaning level 2 de-
pends on the type of floor to be cleaned (e.g. wooden or
stone floor).
The device is set to cleaning level 1 after initial start-up.
The cleaning level setting last used always remains ac-
tivated after interrupting and resuming work.
4. If necessary, activate the boost function for cleaning
stubborn dirt (see also chapter General notes on
operation).
Illustration K
Battery run time
The "Battery" indicator shows the remaining battery run
time:
● 3 LEDs illuminated - 3/3 (full) battery run time
● 2 LEDs illuminated - 2/3 battery run time
● 1 LED illuminated - 1/3 battery run time
Illustration N
Acoustic or optical signals warn of a flat battery.
● An acoustic signal sounds 2 times and the lowest
LED flashes approx. 5 minutes before the battery is
empty.
● An acoustic signal sounds 2 times and the lowest
LED continues to flash approx. 1.5 minutes before
the battery is empty.
● The last LED flashes quicker for 60 seconds when
the battery is empty and the device has switched off.
Emptying the waste water tank
● The "MAX" indicator (red) lights up and an acoustic
signal sounds when the waste water tank is full.
Illustration M
● After 60 seconds, an acoustic signal sounds again
and the device switches off.
● The "MAX" indicator (red) flashes for 10 seconds
once the device is switched off.
● As long as the waste water tank is full and the (red)
"MAX" display lights up, the process restarts and the
following two steps are repeated:
a The device can be switched on again.
b The device runs for another 60 seconds and then
switches off again.
1. Press the ON/OFF switch.
The device switches off.
2. Press the unlocking button for the waste water tank
with your foot and lift the device.
Illustration O
The waste water tank releases from the device.
3. For draining, do not transport the waste water tank
by the top cover, but horizontally with both hands at
the narrow sides.
4. Empty the waste water tank through the opening in
the cap. In the case of adhering dirt deposits, re-
move the cover of the waste water tank and rinse
the waste water tank with tap water.
5. Fit the waste water tank (see Chapter Fitting the
waste water tank).
18
Refilling with detergent
● The "MIN" indicator (blue) lights up and an acoustic
signal sounds when the fresh water tank is empty.
Illustration L
● The acoustic signal sounds once a minute as a re-
minder.
1. Fill the fresh water tank (see Chapter Filling the
fresh water tank).
Interrupting operation
ATTENTION
Damp rollers
Moisture damage to sensitive floors
To prevent damage to sensitive floors through wet roll-
ers, place the device in the parking station during longer
work breaks.
1. Press the ON/OFF switch.
The device switches off.
2. Place the device in the parking station.
Note
If the device is placed on the parking station without a
waste water tank, the unlocking button must be pressed
to remove the device.
Illustration AG
1. Press the ON/OFF switch.
The device switches off.
2. Place the device in the parking station.
Illustration AC
ATTENTION
Adhering dirt deposits
Adhering dirt deposits can damage the device in the
long term.
It is recommended to clean the device completely after
each application.
3. Clean the device (see Chapter Care and service).
Storing the device
ATTENTION
Liquids/moist dirt
Unpleasant odours can develop if the device contains
liquids/moist dirt when stored.
Completely empty the fresh water tank and waste water
tank before storing the device.
Use the cleaning brush to remove hair and dirt particles
from the hair filters in the floor head cover.
Allow the cleaned rollers to dry in the air, e.g. mounted
in the device on the parking station. Do not place the wet
rollers in an enclosed cupboard to dry.
1. Put the empty waste water tank in the cleaning sta-
tion to dry.
a Place the device on the parking station and let it
snap into place.
b Then place the device with the parking station on
the cleaning station.
Illustration AC
2. Fit the cleaned rollers on the device for drying.
Illustration AD
3. Charge the battery (see Chapter Charging pro-
cess).
4. Store the device in a dry room.
Illustration AF
English
Ending operation