Descargar Imprimir esta página

Kärcher Puzzi 8/1 Manual Del Usuario página 11

Ocultar thumbs Ver también para Puzzi 8/1:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 24
Operation
Switching on the device
1. Connect the mains plug.
2. Press the suction switch to switch on the suction tur-
bine.
3. Press the spray switch to switch on the spray pump.
Cleaning mode
ATTENTION
Danger from cleaning solution
Risk of damage
Before using the device, check the object to be cleaned
for colour fastness and water resistance in an inconspic-
uous place.
1. Remove loose dirt from the object to be cleaned.
2. Press the lever on the upholstery nozzle or handle
to spray the cleaning solution.
3. Run over the surface to be cleaned in overlapping
paths. Pull the nozzle backwards (do not push).
4. Adv only: When interrupting work, the suction pipe
(with floor nozzle) can be placed on the carrying
handle of the device.
5. When changing the nozzle, the upholstery nozzle
can be inserted into the holder for accessories.
Switching off the device
1. Switch off the spray switch and the suction switch.
2. Pull out the mains plug.
Empty the wastewater container
1. Switch off the suction switch and the spray switch
when the wastewater container is full.
2. Remove the cover.
3. Remove the wastewater container from the device
and empty it.
Emptying the fresh water tank
1. Switch off the device.
2. Briefly operate the lever on the upholstery nozzle or
handle to relieve pressure.
3. Disconnect the upholstery nozzle or handle from the
spray/suction hose.
4. Hang the suction hose in the fresh water tank.
5. Press the suction switch to switch on the suction tur-
bine.
6. Suck the fresh water tank empty and switch off the
device.
7. Remove the cover.
8. Remove the wastewater container from the device
and empty it.
Flushing the device
1. Connect the upholstery nozzle or handle (with suc-
tion pipe and floor nozzle) to the suction hose.
2. Connect the spray hose coupling to the upholstery
nozzle or handle and latch into place.
3. Pour approximately 2 litres of tap water into the
fresh water tank. Do not add detergents.
4. Press the spray switch to switch on the spray pump.
5. Hold the upholstery or floor nozzle over a drain.
6. Operate the lever on the upholstery nozzle or han-
dle and flush the device for 1 to 2 minutes.
7. Switch off the device.
Each time after use
1. Flush the device.
2. Drain the wastewater container and clean it under
running water.
3. Empty the fresh water tank.
4. Clean the exterior of the device with a damp cloth.
5. To avoid unpleasant smells, remove all water from
the device before long downtimes.
6. Let the device dry thoroughly: Remove the cover or
move it to the side.
Storing the device
1. Wind the mains cable around the carrying handle of
the device and the cover.
Illustration C
2. Store the device in a dry room and secure it against
unauthorised use.
Cleaning methods
1. Spray and vacuum up the cleaning solution in one
step.
Note
Repeated vacuuming without spraying shortens the dry-
ing time.
Heavily soiling or stains
1. Apply cleaning solution with the suction turbine
switched off and let it work for 10 to 15 minutes.
2. Clean the area as with normal soiling.
Upholstery cleaning
1. Adv only: Attach the upholstery nozzle instead of the
floor nozzle (with suction pipe and handle).
2. Use less detergent for sensitive fabrics and spray
the surface at a distance of approx. 200 mm. Then
only vacuum.
● Spray heavily soiled areas in advance and allow the
cleaning solution to work for 5 to 10 minutes.
● Always work from light to shadow (from window to
door).
● Always work from the cleaned to the uncleaned ar-
ea.
● The more sensitive the covering (oriental bridges,
Berber, upholstery fabric) the lower the concentra-
tion of detergent.
● Carpets with jute backs can shrink and bleed in col-
our if the work is too wet.
● Brush wet pile carpets in the direction of the pile af-
ter cleaning when wet (e.g. with a fibre brush or
scrubber).
● Impregnating after wet cleaning prevents the textile
from being quickly soiled again.
● To avoid pressure points or rust stains, do not walk
on or furnish the cleaned area until after it has fully
dried.
● To improve the cleaning result, rinse the object with
clean water after using detergents.
English
Normal soiling
Cleaning tips
11

Publicidad

loading

Este manual también es adecuado para:

Puzzi 8/1 adv